Dell Latitude CSx H Service Manual - Page 25

Pull the bezel out from the LCD panel near the hook locations to release

Get Dell Latitude CSx H PDF manuals and user guides View all Dell Latitude CSx H manuals
Add to My Manuals
Save this manual to your list of manuals
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Dell Latitude CS Portable Computers Service Manual
17
If you have a Sharp or Samsung LCD panel, the inverter is held in place by
two plastic clips located at the top and bottom of the inverter. Press down
on the top of the inverter, and then rotating the top up and slide the
inverter out of the bottom clip.
6.
Remove the old display-assembly interface wire, LCD panel, and display-
assembly inverter wire.
127,&(±²7KH²/&’²SDQHO²LV²IUDJLOH³²+DQGOH²LW²FDUHIXOO\³
NOTE: A new display-assembly top cover, inverter, inverter wire, and bezel are
supplied in the service kit.
127,&(±²%HIRUH²UHPRYLQJ²WKH²SDFNLQJ²EH]HO²IURP²D²QHZ²6KDUS²/&’²
SDQHO´²UHDG²¼5HPRYLQJ²WKH²3DFNLQJ²%H]HO²RQ²D²1HZ²6KDUS²/&’²
3DQHO³Μ²6DPVXQJ²/&’²SDQHOV²GR²QRW²UHTXLUH²D²SDFNLQJ²EH]HO³
7.
Install the new display-assembly interface wire, LCD panel, and inverter
wire into the new top cover provided in the service kit.
8.
Attach the new bezel to the display assembly.
9.
Turn the computer over.
10. Reinstall the main battery in the main battery compartment.
Installation of the new LCD panel is completed.
5HPRYLQJ±WKH±3DFNLQJ±%H]HO±RQ±D±1HZ±6KDUS±/&’±3DQHO
New Sharp LCD panels are shipped with a packing bezel to provide support
and prevent damage. Prepare the new Sharp LCD panel for installation in the
display assembly by performing the following steps:
1.
Carefully peel the protective laminate film off of the LCD panel.
2.
Remove the top-half of the packing bezel.
127,&(±²7KH²/&’²SDQHO²LV²IUDJLOH³²+DQGOH²LW²FDUHIXOO\³
3.
Pull the bezel out from the LCD panel near the hook locations to release
the LCD panel from the bottom half of the packing bezel.
The bottom-half of the packing bezel holds the LCD panel in place with six
hooks (two located on the top left, two located on the top right, and one
located on each side approximately two-thirds up the length of each side).
3DFNLQJ±D±’HIHFWLYH±6KDUS±/&’±3DQHO±IRU±5HWXUQ±6KLSSLQJ
To assemble the Sharp LCD panel and packing bezel for return shipment,
perform the following steps:
1.
Place the LCD panel in to the bottom-half of the packing bezel.
2.
Place the top-half of the packing bezel on the LCD panel.