Dell PowerApp 200 Rack Installation Guide - Page 22

U 1.75 inches

Get Dell PowerApp 200 PDF manuals and user guides View all Dell PowerApp 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

,QVWDOOLQJWKH6OLGH$VVHPEOLHVLQWKH5DFN NOTE: If the slide assemblies were preinstalled by Dell, you can skip this section. You must allow 2 U (3.5 inches) of vertical space for each PowerEdge 2x50 or PowerApp 200 system you install in the rack. NOTE: The vertical rails of the rack are marked by small indentations in 1-U increments (see Figure 6). 1 U (1.75 inches) )LJXUH2QH5DFN8QLW For more information about requirements for installing components in a Dell rack, see the Dell Rack Advisor software available on the Dell Web site at http://support.dell.com. :$51,1*,I\RXDUHLQVWDOOLQJPRUHWKDQRQHV\VWHPLQVWDOOWKHVOLGH DVVHPEOLHVVRWKDWWKHILUVWV\VWHPLVLQVWDOOHGLQWKHORZHVWDYDLODEOHSRVL WLRQLQWKHUDFN To install the slide assemblies in the rack, perform the following steps: 1. Place the front of the template on the vertical rails at the front of the rack where you want to install the system. Ensure that the printing on the template identifies the side facing outwards as the template front. 8 Dell PowerEdge 2x50 and PowerApp 200 Systems Rack Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
8
Dell PowerEdge 2x50 and PowerApp 200 Systems Rack Installation Guide
,QVWDOOLQJ±WKH±6OLGH±$VVHPEOLHV±LQ±WKH±5DFN
NOTE: If the slide assemblies were preinstalled by Dell, you can skip this section.
You must allow 2 U (3.5 inches) of vertical space for each PowerEdge 2
x
50 or
PowerApp 200 system you install in the rack.
NOTE: The vertical rails of the rack are marked by small indentations in 1-U increments
(see Figure 6).
)LJXUH±½º±±2QH±5DFN±8QLW
For more information about requirements for installing components in a Dell rack, see
the Dell Rack Advisor software available on the Dell Web site at
.
:$51,1*±²,I²\RX²DUH²LQVWDOOLQJ²PRUH²WKDQ²RQH²V\VWHP´²LQVWDOO²WKH²VOLGH²
DVVHPEOLHV²VR²WKDW²WKH²ILUVW²V\VWHP²LV²LQVWDOOHG²LQ²WKH²ORZHVW²DYDLODEOH²SRVLµ
WLRQ²LQ²WKH²UDFN³
To install the slide assemblies in the rack, perform the following steps:
1.
Place the front of the template on the vertical rails at the front of the rack where
you want to install the system.
Ensure that the printing on the template identifies the side facing outwards as
the template front.
1 U (1.75 inches)