Dell PowerApp 200 Rack Installation Guide - Page 25

Dell PowerEdge 2x50 and PowerApp 200 Systems Rack Installation Guide11

Get Dell PowerApp 200 PDF manuals and user guides View all Dell PowerApp 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

,QVWDOOLQJWKH6\VWHPVLQWKH5DFN The subsections that follow include instructions for installing the PowerEdge 2x50 and PowerApp 200 systems in the rack. :$51,1*,I\RXDUHLQVWDOOLQJPRUHWKDQRQHV\VWHPLQVWDOOWKHILUVWV\V WHPLQWKHORZHVWDYDLODEOHSRVLWLRQLQWKHUDFN1HYHUSXOOPRUHWKDQRQH FRPSRQHQWRXWRIWKHUDFNDWDWLPH 1. Pull the two interior slide assemblies out of the rack until they lock in the extended position. &$87,21%HFDXVHRIWKHVL]HDQGZHLJKWRIWKHV\VWHPQHYHUDWWHPSWWR LQVWDOOWKHV\VWHPLQWKHVOLGHDVVHPEOLHVE\\RXUVHOI NOTE: Skip to step 3 if your system does not have the optional bezel installed. 2. Remove the optional bezel from the system front panel (see Figure 9): a. Unlock and open the system doors. b. Pivot the two locking levers toward the back of the chassis (see Figure 9). c. Press the tab on each end of the bezel and remove the bezel from the chassis. d. Close the system doors. locking levers (2) tabs (2) )LJXUH5HPRYLQJWKH6\VWHP%H]HO 3. Lift the system into position. Place one hand on the front-bottom of the system and the other hand on the back-bottom of the system. 4. Tilt the system while aligning the back shoulder nuts on the sides of thesystem with the back slots on the slide assemblies (see Figure 10). support.dell.com Dell PowerEdge 2x50 and PowerApp 200 Systems Rack Installation Guide11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
support.dell.com
Dell PowerEdge 2x50 and PowerApp 200 Systems Rack Installation Guide11
,QVWDOOLQJ±WKH±6\VWHPV±LQ±WKH±5DFN
The subsections that follow include instructions for installing the PowerEdge 2
x
50 and
PowerApp 200 systems in the rack.
:$51,1*±²,I²\RX²DUH²LQVWDOOLQJ²PRUH²WKDQ²RQH²V\VWHP´²LQVWDOO²WKH²ILUVW²V\Vµ
WHP²LQ²WKH²ORZHVW²DYDLODEOH²SRVLWLRQ²LQ²WKH²UDFN³²
1HYHU
²SXOO²PRUH²WKDQ²RQH²
FRPSRQHQW²RXW²RI²WKH²UDFN²DW²D²WLPH³
1.
Pull the two interior slide assemblies out of the rack until they lock in the
extended position.
&$87,21±²%HFDXVH²RI²WKH²VL]H²DQG²ZHLJKW²RI²WKH²V\VWHP´²QHYHU²DWWHPSW²WR²
LQVWDOO²WKH²V\VWHP²LQ²WKH²VOLGH²DVVHPEOLHV²E\²\RXUVHOI³
NOTE: Skip to step 3 if your system does not have the optional bezel installed.
2.
Remove the optional bezel from the system front panel (see Figure 9):
a.
Unlock and open the system doors.
b.
Pivot the two locking levers toward the back of the chassis (see Figure 9).
c.
Press the tab on each end of the bezel and remove the bezel from the
chassis.
d.
Close the system doors.
)LJXUH±Àº±±5HPRYLQJ±WKH±6\VWHP±%H]HO
3.
Lift the system into position.
Place one hand on the front-bottom of the system and the other hand on the
back-bottom of the system.
4.
Tilt the system while aligning the back shoulder nuts on the sides of the system
with the back slots on the slide assemblies (see Figure 10).
tabs (2)
locking levers (2)