Home » Dell Manuals » Hubs & Switches » Dell PowerConnect W-3600 » Manual Viewer

Dell PowerConnect W-3600 Installation Guide - Page 18

Safety and Regulatory Compliance

View all Dell PowerConnect W-3600 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Storage Specifications z Storage Temperature Range: 0°C to 50°C (32°F to 122°F) z Storage Humidity Range: 5% - 95% (RH), non-condensing Safety and Regulatory Compliance Dell provides a multi-language document containing country specific restrictions and additional safety and regulatory information for all Dell hardware products. The Dell PowerConnect W-Series Safety, Environmental, and Regulatory Information document is included with this product. CLASS 1 LASER PRODUCT Caution: Use of controls or adjustments of performance or procedures other than those specified in this manual may result in hazardous radiation exposure. This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and IEC 60825-1: 1993, A1: 1997, A2: 2001, IEC 60825-2: 2000. For continued compliance with the above laser safety standards, only approved Class 1 modules from our approved vendors should be installed in Dell products. FCC Class A Device This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Industry Canada This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. 18 | Specifications, Safety & Compliance Dell PowerConnect W-3000 Series Controller | Installation Guide

Section	Page
Dell PowerConnect W-3000 Series Controllers	1
	3
Guide Overview	5
Related Documents	5
Contacting Dell	5
	7
About the PowerConnect W-3000 Series Controllers	7
The PowerConnect W-3000 Series Controllers consists of the following models:	7
Minimum Software Requirements	7
Package Checklist	7
Model Overview	8
Figure 1 W-3200 Front View	8
1000Base-X (SFP) Ports	8
10/100/1000Base-T Gigabit Ethernet Ports	9
Figure 2 Gigabit Ethernet Port Pin-Out	9
Serial Console Port	9
Figure 3 Serial Console Port Pin-Out	9
Table 1 Console Terminal Settings	9
Serial Console Port Adaptor	9
Figure 4 RJ-45 (female) to DB9 (male) Modular Adaptor Conversion	10
Figure 5 W-3200 Rear View	10
AC Power Socket	10
LED Status Indicators	10
Table 2 W-3000 Series Controllers LED Status Indicators	10
	13
Installing the W-3000 Series Controllers	13
The following tools and equipment are required for installing the Dell PowerConnect W-3000 Series Controllers:	13
For a Telecom Rack:	13
For a Server Rack:	13
Installation in a Telecom Rack	13
1. Place a rack mount bracket over the mounting holes on one side of the controller (see Figure 1).	13
2. Secure the bracket to the controller using three 6-32 x 1/4” phillips flat head screws and a suitable screwdriver.	13
3. Repeat these steps on the opposite side of the controller.	13
Figure 1 Rack Mount Brackets	14
4. Mount the controller within your organization’s rack system using four 12-24 x 5/8” phillips flat head screws and a suitable screwdriver (see Figure 2).	14
Figure 2 Rack Mount Installation	14
5. Leave a minimum of four inches (10 cm) of space on the left and right side of the unit for proper air flow and ventilation (see Figure 3).	14
6. Leave additional space in the front and back of the unit to access power cords, network cables, and LED status indicators (see Figure 3).	14
Figure 3 Air Flow Requirements	15
7. Connect the AC power cord (country-specific) to the rear of the unit.	15
8. Plug the opposite end of the power cord into an electrical outlet to power on the controller.	15
Installation in a Server Rack	15
1. Place a rack mount bracket over the mounting holes on one side of the controller (see Figure 1).	15
2. Secure the bracket to the controller using three 6-32 x 1/4” phillips head screws and a suitable screwdriver.	15
3. Repeat these steps on the opposite side of the controller.	15
4. Install the four cage nuts.	15
a. Begin by inserting the lower lip of the cage but over the square opeing in the back of the rail.	15
b. Insert the small end of the cage-nut installation tool through the opening in the rail (from the front), and hook the tool over the top lip of the cage nut.	15
c. Push the cage nut in towards the rail while rotating the tool up and pulling the tool back toward you until the top lip of the cage nut snaps into position.	15
5. Mount the controller within your organization’s rack system using four M6 x 20mm phillips head screws and suitable screwdriver.	15
6. Leave a minimum of four inches (10cm) of space on the left and right side of the unit for proper air flow and ventilation (see Figure 3).	15
7. Leave additional space in front and back of the unit to access power cords, network cables, and LED status indicators (see Figure 3).	15
8. Connect the AC power cord (country-specific) to the rear of the unit.	15
9. Plug the opposite end of the power cord into an electrical outlet to power the controller.	15
Tabletop Deployment	16
1. Insert the four rubber mounting feet to the bottom of the unit.	16
2. Attach side bezels by snapping them into place.	16
3. Place the unit on a hard flat surface.	16
Initial Setup and Network Connectivity	16
Removal	16
1. Disconnect the power to the controller by unplugging the power cord from the electrical outlet.	16
2. Disconnect any other cables or devices attached to the controller.	16
3. Loosen the four rack mount screws securing the controller to your organizations rack system.	16
4. Remove the controller from the rack system.	16
	17
Physical Specifications	17
All Models: 1.75” x 13.8” x 11.7”	17
All Models: 44 mm x 351 mm x 297 mm	17
All Models: 6.5” x 18.2” x 16.5”	17
All Models: 165 mm x 462 mm x 419 mm	17
W-3200: 9.4 lbs/4.3 kgs	17
W-3400/W-3600: 9.7 lbs/4.4 kgs	17
Power Management Specifications	17
Power Consumption	17
Power Specifications (AC Input Requirements)	17
AC Input Voltage: 90-264 V~, Universal Input	17
AC Input Current: 1.5 A	17
AC Input Frequency: 47-63 Hz	17
AC Input Voltage: 90-264 V~, Universal Input	17
AC Input Current: 2.2 A	17
AC Input Frequency: 47-63 Hz	17
Operating Specifications	17
Storage Specifications	18
Safety and Regulatory Compliance	18
FCC Class A Device	18
Industry Canada	18
NOM Information (Mexico Only)	19
Proper Disposal of Dell Equipment	19

Match case Limit results 1 per page

Specifications, Safety & Compliance

Dell PowerConnect W-3000 Series Controller

Installation Guide

Storage Specifications

Storage Temperature Range: 0°C to 50°C (32°F to 122°F)

Storage Humidity Range: 5% - 95% (RH), non-condensing

Safety and Regulatory Compliance

Dell provides a multi-language document containing country specific restrictions and additional safety and

regulatory information for all Dell hardware products. The Dell PowerConnect W-Series Safety, Environmental,

and Regulatory Information document is included with this product.

This product complies with 21 CFR Chapter 1, Subchapter J, Part 1040.10, and IEC 60825-1: 1993, A1: 1997, A2:

2001, IEC 60825-2: 2000.

For continued compliance with the above laser safety standards, only approved Class 1 modules from our

approved vendors should be installed in Dell products.

FCC Class A Device

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause

harmful interference in which case the user will be required to correct the interference at his own expense.

Industry Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

CLASS 1

LASER PRODUCT

Caution:

Use of controls or adjustments of performance or procedures other than those specified in this manual may result

in hazardous radiation exposure.