Dell PowerEdge C5220 Hardware Owner's Manual - Page 45

POST Error Handling, Error Messages, Status Codes

Get Dell PowerEdge C5220 PDF manuals and user guides View all Dell PowerEdge C5220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

POST Error Handling This section provides information on POST error message and handling. Error Messages Error messages are displayed at POST under the following fail conditions: • Hard drive is not present in system • MRC initialization failure in a DIMM module NOTE: You can enable the Pause on Error function in the BIOS setup menu to pause the POST Error Message on Screen at time of display. Error Message Hard-disk drive failure DIMM A1 has been disabled by MRC. DIMM A2 has been disabled by MRC. DIMM A3 has been disabled by MRC. DIMM A4 has been disabled by MRC. Status Codes A status code is a data value used to indicate progress during the boot phase. A subset of these status codes, known commonly as checkpoints, indicate common phases of the BIOS boot process. The status codes can be viewed during POST at the right bottom corner of the screen as shown in Figure 2-1. Using the System Setup Program 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Using the System Setup Program
45
POST Error Handling
This section provides information on POST error message and handling.
Error Messages
Error messages are displayed at POST under the following fail conditions:
•
Hard drive is not present in system
•
MRC initialization failure in a DIMM module
NOTE:
You can enable the
Pause on Error
function in the BIOS setup menu to
pause the POST Error Message on Screen at time of display.
Status Codes
A status code is a data value used to indicate progress during the boot phase.
A subset of these status codes, known commonly as checkpoints, indicate
common phases of the BIOS boot process.
The status codes can be viewed during POST at the right bottom corner of
the screen as shown in Figure 2-1.
Error Message
Hard-disk drive failure
DIMM A1 has been disabled by MRC.
DIMM A2 has been disabled by MRC.
DIMM A3 has been disabled by MRC.
DIMM A4 has been disabled by MRC.