Dell S5248F-ON EMC Networking OS10EE FCoE Deployment with FSB - Page 22

S4148U-ON FCF switch configuration

Get Dell S5248F-ON PDF manuals and user guides View all Dell S5248F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

6 S4148U-ON FCF switch configuration This section details steps to configure the S4148U-ON switches running OS10EE in F_Port mode. 6.1 Prepare switches 6.1.1 Factory default configuration The configuration commands in the sections that follow begin with S4148U-ON switches at their factory default settings. Dell EMC PowerSwitch models running OS10EE can be reset to their default configuration as follows: OS10# delete startup-configuration Proceed to delete startup-configuration [confirm yes/no(default)]:y OS10# reload System configuration has been modified. Save? [yes/no]:n Proceed to reboot the system? [confirm yes/no]:y The switch reboots to its factory default configuration. Repeat on the second S4148U-ON switch. Note: OS10EE at its default settings has Telnet disabled, SSH enabled, and the OOB management interface that is configured to get its IP address using DHCP. The default username and password are both admin. Dell EMC recommends changing the admin password to a complex password during the first login. 6.1.2 Set switch port profile A switch port profile determines the enabled front-panel ports and supported breakout modes on Ethernet and unified ports. Changing the profile removes the existing switch configuration, so the switch port profile is configured first. Switch port profile-3 is used in this deployment to provide twelve 16Gb FC ports for storage connections. Note: See OS10 Enterprise Edition User Guide Release 10.4.2.0 for switch-port profile options and details. To change the switch-port profile from its current setting: OS10# configure terminal OS10(config)# switch-port-profile 1/1 profile-3 Warning: Switch port profile will be applied only after a save and reload. All management port configurations will be retained but all other configurations will be wiped out after the reload. OS10(config)# exit OS10# write memory OS10# reload Proceed to reboot the system? [confirm yes/no]:y 6.2 Configure switches After the switch port profile is set on both S4148U-ONs, the commands in the tables that follow are run to complete the F_Port mode configuration on both switches. 22 Dell EMC Networking OS10EE FCoE Deployment with FSB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
22
Dell EMC Networking OS10EE FCoE Deployment with FSB
6
S4148U-ON FCF switch configuration
This section details steps to configure the S4148U-ON switches running OS10EE in F_Port mode.
6.1
Prepare switches
6.1.1
Factory default configuration
The configuration commands in the sections that follow begin with S4148U-ON switches at their factory
default settings. Dell EMC PowerSwitch models running OS10EE can be reset to their default configuration as
follows:
OS10#
delete startup-configuration
Proceed to delete startup-configuration [confirm yes/no(default)]:
y
OS10#
reload
System configuration has been modified. Save? [yes/no]:
n
Proceed to reboot the system? [confirm yes/no]:
y
The switch reboots to its factory default configuration. Repeat on the second S4148U-ON switch.
Note:
OS10EE at its default settings has Telnet disabled, SSH enabled, and the OOB management interface
that is configured to get its IP address using DHCP. The default username and password are both admin. Dell
EMC recommends changing the admin password to a complex password during the first login.
6.1.2
Set switch port profile
A switch port profile determines the enabled front-panel ports and supported breakout modes on Ethernet and
unified ports. Changing the profile removes the existing switch configuration, so the switch port profile is
configured first. Switch port profile-3 is used in this deployment to provide twelve 16Gb FC ports for storage
connections.
Note:
See
OS10 Enterprise Edition User Guide Release 10.4.2.0
for switch-port profile options and details.
To change the switch-port profile from its current setting:
OS10#
configure terminal
OS10(config)#
switch-port-profile 1/1 profile-3
Warning: Switch port profile will be applied only after a save and reload.
All management port configurations will be retained but all other
configurations will be wiped out after the reload.
OS10(config)#
exit
OS10#
write memory
OS10#
reload
Proceed to reboot the system? [confirm yes/no]:
y
6.2
Configure switches
After the switch port profile is set on both S4148U-ONs, the commands in the tables that follow are run to
complete the F_Port mode configuration on both switches.