Dell Vostro 5301 Service Manual - Page 46

System board, Removing the system board

Get Dell Vostro 5301 PDF manuals and user guides View all Dell Vostro 5301 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Steps 1. Align and place the I/O board on the palm-rest and keyboard assembly. 2. Replace the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly. 3. Connect the I/O-board cable and close the latch to secure the cable to the I/O board. 4. Adhere the tape that secures the I/O-board cable to the fan. 5. Adhere the tape that secures the I/O-board cable to the I/O board. Next steps 1. Install the fan. 2. Install the base cover. 3. Follow the procedure in After working inside your computer. System board Removing the system board Prerequisites 1. Follow the procedure in Before working inside your computer. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You must make the appropriate changes again after you replace the system board. NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can reconnect the cables correctly after you replace the system board. 2. Remove the base cover. 3. Remove the 4-cell battery or the 2-cell battery. 4. Remove the fan. 5. Remove the heat sink. 46 Disassembly and reassembly

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Steps
1.
Align and place the I/O board on the palm-rest and keyboard assembly.
2.
Replace the two screws (M2x3) that secure the I/O board to the palm-rest and keyboard assembly.
3.
Connect the I/O-board cable and close the latch to secure the cable to the I/O board.
4.
Adhere the tape that secures the I/O-board cable to the fan.
5.
Adhere the tape that secures the I/O-board cable to the I/O board.
Next steps
1.
Install the
fan
.
2.
Install the
base cover
.
3.
Follow the procedure in
After working inside your computer
.
System board
Removing the system board
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
NOTE:
Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE:
Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program.
You must make the appropriate changes again after you replace the system board.
NOTE:
Before disconnecting the cables from the system board, note the location of the connectors so that you can
reconnect the cables correctly after you replace the system board.
2.
Remove the
base cover
.
3.
Remove the
4-cell battery
or the
2-cell battery
.
4.
Remove the
fan
.
5.
Remove the
heat sink
.
46
Disassembly and reassembly