Dell XPS 17 9700 Service Manual - Page 50

Antenna, Removing the antennas

Get Dell XPS 17 9700 PDF manuals and user guides View all Dell XPS 17 9700 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

15. Connect the display cable and the camera cable to the system board. 16. Align the screw holes on the display-cable bracket with the screw holes on the system board. 17. Replace the two screws (M2x4) that secure the display-cable bracket to the palm-rest and keyboard assembly. NOTE: Apply sufficient torque when tightening the two screws (M2x4) to avoid damaging the screw threads. Next steps 1. Install the display assembly. 2. Install the I/O board. 3. Install the right fan. 4. Install the left fan. 5. Install the heat sink. 6. Install the M.2 2230 solid-state drive or the M.2 2280 solid-state drive in the SSD2 slot. 7. Install the M.2 2230 solid-state drive or the M.2 2280 solid-state drive in the SSD1 slot. 8. Install the memory modules. 9. Install the battery. 10. Install the base cover. 11. Follow the procedure in After working inside your computer. Antenna Removing the antennas Prerequisites 1. Follow the procedure in Before working inside your computer. NOTE: The Service Tag of your computer is stored in the system board. Enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup program. Make the appropriate changes again after you replace the system board. NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can reconnect the cables correctly after you replace the system board. 2. Remove the base cover. 3. Remove the battery. 4. Remove the memory modules. 5. Remove the M.2 2230 solid-state drive or the M.2 2280 solid-state drive from the SSD1 slot. 6. Remove the M.2 2230 solid-state drive or the M.2 2280 solid-state drive from the SSD2 slot. 7. Remove the heat sink. NOTE: The system board can be removed or installed together with the heat sink attached. This simplifies the procedure and avoids breaking the thermal bond between the system board and the heat sink. 8. Remove the right fan. 9. Remove the left fan. 10. Remove the I/O board. 11. Remove the display assembly. 12. Remove the system board. About this task The following image indicates the location of the antennas and provides a visual representation of the removal procedure. 50 Removing and installing components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
15.
Connect the display cable and the camera cable to the system board.
16.
Align the screw holes on the display-cable bracket with the screw holes on the system board.
17.
Replace the two screws (M2x4) that secure the display-cable bracket to the palm-rest and keyboard assembly.
NOTE:
Apply sufficient torque when tightening the two screws (M2x4) to avoid damaging the screw threads.
Next steps
1.
Install the
display assembly
.
2.
Install the
I/O board
.
3.
Install the
right fan
.
4.
Install the
left fan
.
5.
Install the
heat sink
.
6.
Install the
M.2 2230 solid-state drive
or the
M.2 2280 solid-state drive
in the SSD2 slot.
7.
Install the
M.2 2230 solid-state drive
or the
M.2 2280 solid-state drive
in the SSD1 slot.
8.
Install the
memory modules
.
9.
Install the
battery
.
10.
Install the
base cover
.
11.
Follow the procedure in
After working inside your computer
.
Antenna
Removing the antennas
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
NOTE:
The Service Tag of your computer is stored in the system board. Enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE:
Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup
program. Make the appropriate changes again after you replace the system board.
NOTE:
Before disconnecting the cables from the system board, note the location of the connectors so that you can
reconnect the cables correctly after you replace the system board.
2.
Remove the
base cover
.
3.
Remove the
battery
.
4.
Remove the
memory modules
.
5.
Remove the
M.2 2230 solid-state drive
or the
M.2 2280 solid-state drive
from the SSD1 slot.
6.
Remove the
M.2 2230 solid-state drive
or the
M.2 2280 solid-state drive
from the SSD2 slot.
7.
Remove the
heat sink
.
NOTE:
The system board can be removed or installed together with the heat sink attached. This simplifies the
procedure and avoids breaking the thermal bond between the system board and the heat sink.
8.
Remove the
right fan
.
9.
Remove the
left fan
.
10.
Remove the
I/O board
.
11.
Remove the
display assembly
.
12.
Remove the
system board
.
About this task
The following image indicates the location of the antennas and provides a visual representation of the removal procedure.
50
Removing and installing components