Dell XPS 410 Owner's Manual - Page 114

Replace the drive panel insert see Replacing the Drive-Panel Insert

Page 114 highlights

5 Disconnect the USB cable on the back of the Media Card Reader. Disconnect the other end of the cable from the USB connector on the system board (see "System Board Components" on page 81). Remove the cable from any clips and lift out of the computer. 2 1 3 1 sliding plate 2 sliding plate lever 3 Media Card Reader (not present on all computers) 6 Pull the sliding plate to the right and hold in place. Then, slide the drive out the front of the computer. 7 Replace the drive panel insert (see "Replacing the Drive-Panel Insert" on page 102). 8 Replace the drive panel (see "Replacing the Drive Panel" on page 103). 9 Replace the computer cover (see "Replacing the Computer Cover" on page 121). 10 Power up the system and enter system setup (see "System Setup" on page 127). Set the USB for FlexBay value to OFF. 114 Removing and Installing Parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172

114
Removing and Installing Parts
5
Disconnect the USB cable on the back of the Media Card Reader. Disconnect the other end of the
cable from the USB connector on the system board (see "System Board Components" on page 81).
Remove the cable from any clips and lift out of the computer.
6
Pull the sliding plate to the right and hold in place. Then, slide the drive out the front of the computer.
7
Replace the drive panel insert (see "Replacing the Drive-Panel Insert" on page 102).
8
Replace the drive panel (see "Replacing the Drive Panel" on page 103).
9
Replace the computer cover (see "Replacing the Computer Cover" on page 121).
10
Power up the system and enter system setup (see "System Setup" on page 127). Set the
USB for
FlexBay
value to
OFF
.
1
sliding plate
2
sliding plate lever
3
Media Card Reader (not
present on all computers)
3
1
2