Dell XPS 410 Owner's Manual - Page 99

Remove the card driver from the operating system., If you removed a sound card

Get Dell XPS 410 PDF manuals and user guides View all Dell XPS 410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

NOTICE: Ensure that you release the securing tab to unseat the card. If the card is not removed correctly, the system board may be damaged. 6 Release the securing tab on the card slot to unseat the card. 7 If you are removing the card permanently, install a filler bracket in the empty card-slot opening. If you need a filler bracket, contact Dell (see "Contacting Dell" on page 137). NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep dust and dirt out of your computer. 8 Reseat the card retention mechanism in the tabs and pivot downward to snap it into place. 9 Close the card retention door to snap it into place, securing the card(s). NOTE: For full-length PCI-E cards, if a "piano" bracket is present on your computer you need to rotate it down into place. NOTICE: To connect a network cable, first plug the cable into the network device and then plug the cable into the computer. 10 Replace the computer cover, reconnect the computer and devices to electrical outlets, and then turn them on. 11 Remove the card driver from the operating system. 12 If you removed a sound card: a Enter system setup, select Integrated Audio Controller, and then change the setting to On. b Connect external audio devices to the integrated audio connectors on the back panel of the computer. 13 If you removed an add-in network connector: a Enter system setup, select Integrated NIC Controller, and then change the setting to On. b Connect the network cable to the integrated connector on the back panel of the computer. NOTE: Install any drivers required for the card as described in the card documentation. Removing and Installing Parts 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Removing and Installing Parts
99
NOTICE:
Ensure that you release the securing tab to unseat the card. If the card is not removed correctly, the
system board may be damaged.
6
Release the securing tab on the card slot to unseat the card.
7
If you are removing the card permanently, install a filler bracket in the empty card-slot opening.
If you need a filler bracket, contact Dell (see "Contacting Dell" on page 137).
NOTE:
Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the
computer. The brackets also keep dust and dirt out of your computer.
8
Reseat the card retention mechanism in the tabs and pivot downward to snap it into place.
9
Close the card retention door to snap it into place, securing the card(s).
NOTE:
For full-length PCI-E cards, if a "piano" bracket is present on your computer you need to rotate it down into
place.
NOTICE:
To connect a network cable, first plug the cable into the network device and then plug the cable into the
computer.
10
Replace the computer cover, reconnect the computer and devices to electrical outlets, and then turn
them on.
11
Remove the card driver from the operating system.
12
If you removed a sound card:
a
Enter system setup, select
Integrated Audio Controller
, and then change the setting to
On
.
b
Connect external audio devices to the integrated audio connectors on the back panel of the
computer.
13
If you removed an add-in network connector:
a
Enter system setup, select
Integrated NIC Controller
, and then change the setting to
On
.
b
Connect the network cable to the integrated connector on the back panel of the computer.
NOTE:
Install
any drivers required for the card as described in the card documentation.