Dell XPS M1710 MXG061 XPS M1710 Service Manual - Page 49

CAUTION, NOTICE, Product, Information Guide

Get Dell XPS M1710 MXG061 PDF manuals and user guides View all Dell XPS M1710 MXG061 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

1 display panel 4 grounding wire and captive screw 2 M2 x 3-mm screws (8) 3 display back cover CAUTION: Before you begin the following procedure, follow the safety instructions in the Product Information Guide. NOTICE: To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an unpainted metal surface (such as the back panel) on the computer. NOTICE: To help prevent damage to the system board, remove the main battery (see Before Working Inside Your Computer) before working inside the computer. 1. Follow the instructions in Before Working Inside Your Computer. 2. Remove the display assembly (see Removing the Display Assembly). 3. Remove the display bezel (see Removing the Display Bezel). 4. Loosen the captive ground screw that attaches the display-panel ground wire to the display back cover. 5. Remove the eight M2 x 3-mm screws (four on each side of the display panel). 6. Lift the display panel out of the display back cover. 7. Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display connector. 8. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
file:///C|/Users/santhosh_v.ASIA-PACIFIC/Desktop/Hawke/New%20folder/display.htm[2/21/2014 11:23:47 AM]
1
display panel
2
M2 x 3-mm screws (8)
3
display back cover
4
grounding wire and captive screw
CAUTION:
Before you begin the following procedure, follow the safety instructions in the
Product
Information Guide
.
NOTICE:
To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by touching an
unpainted metal surface (such as the back panel) on the computer.
NOTICE:
To help prevent damage to the system board, remove the main battery (see
Before Working Inside Your
Computer
) before working inside the computer.
1. Follow the instructions in
Before Working Inside Your Computer
.
2. Remove the display assembly (see
Removing the Display Assembly
).
3. Remove the display bezel (see
Removing the Display Bezel
).
4. Loosen the captive ground screw that attaches the display-panel ground wire to the display back cover.
5. Remove the eight M2 x 3-mm screws (four on each side of the display panel).
6. Lift the display panel out of the display back cover.
7. Press in both sides of the top flex-cable connector, and pull the top flex-cable connector away from the display
connector.
8. Use the pull-tab to disconnect the bottom flex-cable connector from the inverter connector.