Denon AVR-1804 Owners Manual - Page 37

Example: Stereo - optical

Get Denon AVR-1804 PDF manuals and user guides View all Denon AVR-1804 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

ENGLISH 3 Select the play mode. Press the SURROUND MODE button, then turn the SELECT knob. Example: Stereo (Main unit) (Remote control unit) To select the surround mode while adjusting the surround parameters, tone defeat or tone control, press the surround mode button then operate the selector. (Main unit) 4 Start playback on the selected component. • For operating instructions, refer to the component's manual. 5 Adjust the volume. The volume level is displayed on the master volume level display. (Main unit) (Remote control unit) The volume can be adjusted within the range of -70 to 0 to 18 dB, in steps of 1 dB. However, when the channel level is set as described on page 44, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume is adjusted to "18 dB - (Maximum value of channel level)".) Input mode when playing DTS sources • Noise will be output if DTS-compatible CDs or LDs are played in the "ANALOG" or "PCM" mode. When playing DTS-compatible sources, be sure to connect the source component to the digital input jacks (OPTICAL/COAXIAL) and set the input mode to "DTS". Input mode display • In the AUTO mode AUTO INPUT PCM DTS • In the DIGITAL PCM mode AUTO INPUT PCM DTS • In the DIGITAL DTS mode AUTO INPUT PCM DTS • In the ANALOG mode AUTO INPUT PCM DTS Input signal display • DOLBY DIGITAL SIGNAL DIGITAL • DTS SIGNAL DIGITAL • PCM SIGNAL DIGITAL One of these lights, depending on the input signal. DIGITAL ANALOG DIGITAL DIGITAL ANALOG The DIGITAL indicator lights when digital signals are being input properly. If the DIGITAL indicator does not light, check whether the digital input component setup (page 26) and connections are correct and whether the component's power is turned on. NOTE: • The DIGITAL indicator will light when playing CD-ROMs containing data other than audio signals, but no sound will be heard. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
37
3
Select the play mode.
Press the SURROUND MODE button, then turn the SELECT
knob.
(Main unit)
(Remote control unit)
4
Start playback on the selected component.
•
For operating instructions, refer to the component
’
s manual.
5
Adjust the volume.
To select the surround mode while
adjusting the surround parameters,
tone defeat or tone control, press
the surround mode button then
operate the selector.
(Main unit)
(Main unit)
(Remote control unit)
The volume level is
displayed on the
master volume level
display.
The volume can be adjusted within the range of
–
70 to 0
to 18 dB, in steps of 1 dB. However, when the channel
level is set as described on page 44, if the volume for any
channel is set at +1 dB or greater, the volume cannot be
adjusted up to 18 dB. (In this case the maximum volume
is adjusted to
“
18 dB
—
(Maximum value of channel
level)
”
.)
Input mode when playing DTS sources
•
Noise will be output if DTS-compatible CDs or LDs are played in the
“
ANALOG
”
or
“
PCM
”
mode.
When playing DTS-compatible sources, be sure to connect the
source component to the digital input jacks (OPTICAL/COAXIAL)
and set the input mode to
“
DTS
”
.
Input mode display
ANALOG
DIGITAL
DIGITAL
DIGITAL
ANALOG
AUTO
PCM
DTS
INPUT
AUTO
PCM
DTS
INPUT
AUTO
PCM
DTS
INPUT
AUTO
PCM
DTS
INPUT
•
In the AUTO mode
•
In the DIGITAL PCM mode
•
In the DIGITAL DTS mode
•
In the ANALOG mode
One of these lights, depending on the
input signal.
Input signal display
SIGNAL
DIGITAL
DIGITAL
DIGITAL
SIGNAL
SIGNAL
•
DOLBY DIGITAL
•
DTS
•
PCM
The
indicator lights when digital signals are being input
properly. If the
indicator does not light, check whether
the digital input component setup (page 26) and connections are
correct and whether the component
’
s power is turned on.
DIGITAL
DIGITAL
NOTE:
•
The
indicator will light when playing CD-ROMs
containing data other than audio signals, but no sound will be
heard.
DIGITAL
Example: Stereo
ENGLISH