Denon AVR-2311CI Owners Manual - English - Page 57

ENGLISH Audio/Video Adjust nnAudyssey Settings Default settings are underlined. Set MultEQ®, Dynamic EQ® and Dynamic Volume®. These can be selected after Audyssey® Auto Setup has been performed. For additional information on Audyssey technology, please see page 80. NOTE If you have not performed Auto Setup, or if you change the speaker settings after performing Auto Setup, you may not be able to select Dynamic EQ/Dynamic Volume, and "Run Audyssey" may be displayed. In this case, either perform Audyssey Auto Setup over again or perform "Restore" (vpage 10) to return to the settings after Audyssey Auto Setup was run. Setting items MultEQ Select one equalizer from three modes. MultEQ corrects both time and frequency response problems in the listening area based on Audyssey Auto Setup calibration. We recommend "Audyssey". MultEQ is the prerequisite function for Dynamic EQ and Dynamic Volume. Setting details Audyssey : Optimize the frequency response of all speakers. Audyssey Byp.L/R : Optimize frequency response of speakers except front L and R speakers. Audyssey Flat : Optimize frequency response of all speakers to flat response. Manual : Apply frequency response set with "Manual EQ" (vpage 55). OFF : Turn "MultEQ" equalizer off. • "Audyssey", "Audyssey Byp. L/R" and "Audyssey Flat" can be selected after Audyssey Auto Setup has been performed. "Audyssey" is automatically selected after performing Audyssey Auto Setup. When "Audyssey", "Audyssey Byp. L/R" or "Audyssey Flat" is selected, illuminates. • After running Audyssey Auto Setup, if the Speaker Configuration, Distance, Channel Level, and Crossover Frequency have changed without increasing the number of speakers measured, only illuminates. • Pressing MULTEQ makes this setting. NOTE • "MultEQ" and "Manual" cannot be selected when "EQ Customize" is set to "Not Used" (vpage 61). • When using headphones, "MultEQ" is automatically set to "OFF". Setting items Dynamic EQ® Solve the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Setting details ON : Use Dynamic EQ. OFF : Do not use Dynamic EQ. • is displayed when set to "ON". • Buttons on the remote control unit or main unit can be used for operations. GOperations with the remote control unitH Press DYN EQ/VOL. Each time DYN EQ/VOL is pressed, the setting is changed as shown below. Dynamic EQ : ON Dynamic Volume : Midnight Dynamic EQ : ON Dynamic Volume : Evening Dynamic EQ : OFF Dynamic EQ : ON Dynamic Volume : OFF Dynamic Volume : OFF GOperations with the main unitH Press DYNAMIC EQ. Each time DYNAMIC EQ is pressed, the setting is changed as shown below. Dynamic EQ : ON Dynamic Volume : Day Dynamic EQ : ON Dynamic EQ : OFF Reference Level Offset Audyssey Dynamic EQ is referenced to the standard film mix level. It makes adjustments to maintain the reference response and surround envelopment when the volume is turned down from 0 dB. However, film reference level is not always used in music or other non-film content. Dynamic EQ Reference Level Offset provides three offsets from the film level reference (5 dB, 10 dB, and 15 dB) that can be selected when the mix level of the content is not within the standard. 0dB (Film Ref) : This is the default setting and should be used when listening to movies. 5dB : Select this setting for content that has a very wide dynamic range, such as classical music. 10dB : Select this setting for jazz or other music that has a wider dynamic range. This setting should also be selected for TV content as that is usually mixed at 10 dB below film reference. 15dB : Select this setting for pop/rock music or other program material that is mixed at very high listening levels and has a compressed dynamic range. Setting is enabled when "Dynamic EQ" is "ON" (vpage 54). 54 Remote control operation buttons Move the cursor (Up/Down/Left/Right) Confirm the setting Return to previous menu