Denon POA-3012CI Owners Manual - English - Page 12

External Controller

Get Denon POA-3012CI - Multi-Zone Audio Distribution Power Amplifier PDF manuals and user guides
UPC - 083795000196
View all Denon POA-3012CI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Getting Started Connections Setup Operations Troubleshooting Specifications ENGLISH External Controller RS-232C connector This connector is used for an external controller. b If you wish to control the POA-3012CI from an external controller using the RS-232C connector, perform the operation below beforehand. q Turn the POA-3012CI's power. w Turn off the POA-3012CI's power from the external controller. e Check that the POA-3012CI is in the standby mode. Trigger output jack The power of an external device equipped with a trigger input jack can be turned on and off in association with operations on the POA-3012CI. • Output level: 250 mA / 12 V Check the trigger input conditions of the connected device. • If the trigger input level of the connected device is higher than 250 mA / 12 V and depending on the short-circuiting conditions, the POA-3012CI's protection circuit may be activated, in which case "TRIGGER OUT OVER LOAD" appears on the display. If this happens, turn off the POA3012CI's power and disconnect the connected device.  Master trigger input jack The "POWER CONFIGURATION" setting is valid at the time of a "MASTER TRIGGER". Voltage input to the MASTER TRIGGER input terminal and operating status of the POA-3012CI: At DC 3 ~ 30 V ON At DC 0 V STANDBY ZONE trigger input jack The ZONE TRIGGER ON MODE setting is valid at the time of a "TRIGGER IN". Voltage input to the TRIGGER IN input terminal and operating status of the power amplifier of each ZONE: At DC 3 ~ 30 V ON At DC 0 V STANDBY

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
¹
Getting Started
Setup
Operations
Troubleshooting
ENGLISH
Specifications
RS-232C connector
This connector is used for an external controller.
b
If you wish to control the POA-3012CI from
an external controller using the RS-232C
connector,
perform
the
operation
below
beforehand.
q
Turn the POA-3012CI’s power.
w
Turn off the POA-3012CI’s power from the
external controller.
e
Check that the POA-3012CI is in the standby
mode.
Trigger output jack
The power of an external device equipped with
a trigger input jack can be turned on and off in
association with operations on the POA-3012CI.
• Output level: 250 mA / 12 V
Check the trigger input conditions of the
connected device.
• If the trigger input level of the connected device
is higher than 250 mA / 12 V and depending on
the short-circuiting conditions, the POA-3012CI’s
protection circuit may be activated, in which
case “TRIGGER OUT OVER LOAD” appears on
the display. If this happens, turn off the POA-
3012CI’s power and disconnect the connected
device.
External Controller
Master trigger input jack
The “POWER CONFIGURATION” setting is valid
at the time of a “MASTER TRIGGER”.
Voltage input to the MASTER TRIGGER input
terminal and operating status of the POA-3012CI:
At DC 3 ~ 30 V····················ON
At DC 0 V ····························STANDBY
ZONE trigger input jack
The ZONE TRIGGER ON MODE setting is valid at
the time of a “TRIGGER IN”.
Voltage input to the TRIGGER IN input terminal
and operating status of the power amplifier of
each ZONE:
At DC 3 ~ 30 V····················ON
At DC 0 V ····························STANDBY
Connections