Denon POA-3012CI Owners Manual - English - Page 22
Troubleshooting, Specifications - dimensions
UPC - 083795000196
View all Denon POA-3012CI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
Getting Started Connections Setup Operations Troubleshooting Specifications ENGLISH Troubleshooting Specifications Check the following before assuming there is a problem with the set: 1. Are all connections proper? 2. Is the set being operated as described in the owner's manual? 3. Are the speakers and input components being operated properly? If the set does not seem to be operating properly, check the points listed below. If these points do not apply, the set may be damaged. Turn off the power immediately and contact your store of purchase. Symptom Cause Countermeasure When the power is • The power supply cord's plug is • Make sure the unit is correctly turned on, the power not fully plugged in. plugged in and switched on at indicator does not the mains socket. light and no sound is produced. The power indicator • The speaker cables are not fully • Connect securely. lights but no sound connected. is produced. • The device you want to listen to • Insure the correct input is has not been selected. selected. • The volume control is set to • Set to an appropriate level. minimum. • The input cable is not fully • Connect securely. connected. • The speaker cable is not • Connect the speaker as connected properly for the required for the Operation Mode operation mode. (NORMAL MODE or BRIDGED MODE). • The input connector is not • Connect the input connector connected properly. correctly (in the case of BRIDGED input for each ZONE, input to an even-numbered channel.) • The "Turn On" command is not • Send the "Turn On" command input from the external terminal from the external device. when the ZONE TRIGGER ON MODE is set to ON LINE (the ZONE operation mode indicator is not lit). • Trigger voltage is not input to • Input the trigger voltage from the TRIGGER IN terminal from the external device. the external device when the ZONE TRIGGER ON MODE is set to "TRIG. IN". Page 10 5 7 17 7 5 7 9, 14 9, 14 Rated output: 12-channel driving, NORMAL operation: 30 W x 12 ch (8 Ω/ohms, DIN 1 kHz with 0.7 % T.H.D.) 50 W x 12 ch (4 Ω/ohms, DIN 1 kHz with 0.7 % T.H.D.) 6-channel driving, BRIDGED operation: 100 W x 6 ch (8 Ω/ohms, DIN 1 kHz with 0.7 % T.H.D.) Total harmonic distortion: 0.05% (Rated output: -3 dB, 8 Ω/ohms, 1 kHz) Output terminals: Speaker 4 ~ 16 Ω/ohms (NORMAL operation) Speaker 8 ~ 16 Ω/ohms (BRIDGED operation) Input sensitivity / Input impedance: 550 mV / 47 kΩ/kohms (NORMAL operation) 275 mV / 47 kΩ/kohms (BRIDGED operation) Gain: 29 dB (NORMAL operation) 35 dB (BRIDGED operation) Frequency response: 5 Hz ~ 40 kHz (Low cut filter: OFF) S/N raito: 95 dB (input terminals short-circuited, with A-weightied network) Low cut filter: Cut off freguency 80 Hz (-12 dB/oct. Low cut filter: ON) Trigger in level: 3 ~ 30 V DC Trigger out level: 12 V DC, 250 mA MAX Power Supply: AC 120 V, 60 Hz (North America model) / AC 230 V, 50Hz (Europe model) Power Consumption: 2.5 A (North America model) / 230 W (Europe model) Standby: 0.5 W or less (When the "POWER CONFIGURATION" is set to "POWER BUTTON") Maximum external dimension: 434 (W) x 171 (H) x 410 (D) mm (17-3/32" x 6-47/64" x 16-9/64") Weight: 19.0 kg (Approx 41 lbs 14.2 oz) b For purposes of improvement, specifications and design are subject to change without notice. 19