Dewalt DWE43066N Instruction Manual - Page 8

English minimum wire size. The following table shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The lower the gauge number, the heavier the cord. Minimum Gauge for Cord Sets Volts Total Length of Cord in Feet (meters) 120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7) 240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4) Ampere Rating More Not Than More American Wire Gauge Than 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended The label on your tool may include the following symbols. The symbols and their definitions are as follows: V volts or AC/DC..... alternating or Hz hertz direct current min minutes Class II or DC....... direct current Class I Construction Construction (double insulated) (grounded) no no load speed .../min per minute n rated speed BPM beats per minute earthing terminal IPM impacts per minute RPM revolutions per safety alert symbol visible radiation minute wear respiratory sfpm surface feet per minute SPM strokes per minute protection wear eye protection A amperes W watts or AC alternating current wear hearing protection read all documentation Lanyard Connection (Fig. B) DWE43066N, DWE43115N Safety Warnings Specific for Use At Height • Always keep the tool and accessories tethered when working "at height". [Maximum lanyard length: 6.5 ft (2m)] • Use only with lanyards appropriate for this tool type and rated for at least 6.0 lbs (2.72 Kg). • Crush, cut or entanglement hazard. Do not use near moving parts, mechanisms or running machinery. • Do not anchor the tool lanyard to anything on your body. Anchor to a rigid structure that can withstand the forces of a dropped tool. • Make sure the lanyard is properly secure at each end prior to use. • Inspect tool and lanyard before each use for damage and proper function (including fabric and stitching). Do not use if damaged or not functioning properly. • Do not alter the lanyard connection or use in a manner other than as instructed in this manual. • Only attach tool to a lanyard with a locking carabiner. Do not attach by looping or knotting the lanyard. Do not use rope or cord. • Electrical shock hazard. Be sure power is off when working in high voltage areas. Some lanyards are conductive. • Dropped tools will swing on the lanyard, which could cause injury or loss of balance. • Do not carry the tool by attachment device or the lanyard. • Do not attach more than one tool to each lanyard. • Only use appropriate DeWALT brand attachment point. NEVER modify tools to create attachment points. • Only transfer the tool between hands while properly balanced in a stable orientation. • Do not attach lanyards to tool in a way that keeps guards, switches or lock-offs from operating properly. • Avoid getting tangled in the lanyard. • Keep lanyard away from the cutting area of the tool. • Do not use lanyards or attachment devices to get additional leverage from the tool. • Do not use for personal fall protection. • Falling object hazard! Only change accesories and attachments where a dropped object won't cause a hazard below you. Consult your AHJ or site supervisor for procedures for working at height. • Use multi-action and screw gate type carabineers. Do not use single action spring clip carabineers. The lanyard connection 21 is intended for use by competent personnel, who are trained and knowledgeable regarding working with tools in and around machinery and "at height".A lanyard connection may be added to certain models by an authorized service center. Fig. B 21 SAVE THESE INSTRUCTIONS FOR FUTURE USE Motor Be sure your power supply agrees with the nameplate marking. Voltage decrease of more than 10% will cause loss of power and overheating. DeWALT tools are factory tested; if this tool does not operate, check power supply. COMPONENTS (FIG. A) WARNING: Never modify the power tool or any part of it. Damage or personal injury could result. Refer to Figure A at the beginning of this manual for a complete list of components. 6