Dewalt DWE46125 Instruction Manual - Page 7

Minimum Gauge for Cord Sets Volts Total Length of Cord in Feet (meters) 120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7) 240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4) Ampere Rating More Not Than More American Wire Gauge Than 0 6 18 16 16 14 6 10 18 16 14 12 10 12 16 16 14 12 12 16 14 12 Not Recommended  WARNING: If the plug or power cord is damaged, it must be replaced by the manufacturer or its representative or by an equally qualified person to avoid danger. The label on your tool may include the following symbols. The symbols and their definitions are as follows: V volts or AC/DC..... alternating or Hz hertz direct current min minutes Class II or DC....... direct current Construction Class I Construction (double insulated) (grounded) no no load speed .../min per minute n rated speed BPM beats per minute earthing terminal IPM impacts per minute safety alert symbol RPM revolutions per visible radiation minute wear respiratory sfpm surface feet per protection minute wear eye SPM strokes per minute protection A amperes W watts or AC alternating current wear hearing protection read all documentation SAVE THESE INSTRUCTIONS FOR FUTURE USE Intended Use Your cutting shroud has been designed for professional concrete and masonry or stone cutting, or tuckpoint applications with a Diamond coated wheel that is designed for the application. It is not intended for use with metal or wood. Using the appropriate grinder, wheel and dust extractor vacuum it can be used to remove the vast majority of static and airborne dust which without the use of the cutting shroud could otherwise contaminate the working environment or pose an increased health risk to the operator and those in close proximity. DO NOT use under wet conditions or in presence of flammable liquids or gases. The cutting shroud is a professional tool. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool. English Cutting Shroud / Grinder Compatible List DWE46125 Keyless gear case: DWE43214, DWE43214N, DWE43214NVS, DWE43240INOX, DWE43231VS, DWE43244N, DWE43240VS, DWE46253, DWE46202, DWE43265N, DWE43840CN DWE43113, DWE43115, DWE43115N, DWE43066, DWE43066N, DWE43116, DWE43116N, DWE43114, DWE43114N, DWE43131, DWE43144, DWE43144N, DWE43140, DWE46103, DWE46153, DWE46155 DWE402G, DWE402K, DWE402, DWE402N DWE4222, DWE4222N, DWE4214 DWE4020, DWE4120, DWE4011 DCG413, DCG414, DCG414, DCG415, DCG416, DCG418 DWE46127 DWE4517, DWE4519, DWE4557, DWE4559N, DWE4559CN, D28499X, DWE4597, DWE4597N, DWE4599N NOTE: The DWE46125 must be only used with 4.5" (115 mm) or 5" (125 mm) accessories. The DWE46127 must be only used with 7" (180 mm) accessories. ASSEMBLY AND ADJUSTMENTS  WARNING: To reduce the risk of serious personal injury, turn unit off and disconnect it from power source before making any adjustments or removing/installing attachments or accessories. An accidental start-up can cause injury. Mounting and Removing Cutting Shroud (Fig. B-D) 1. Follow the mounting and removing guard instructions in the tool manual to remove the guard from grinder. Retain the original parts from your grinder to properly reassemble the grinder guard. 2. To the mount DWE46125 cutting shroud on a keyless gear case, remove the screw 16 shown in Figure B. 3. Insert the supplied stop screw 18 as shown in Figure C. Then mount cutting shroud. Then mount cutting shroud. Refer to the Cutting Shroud / Grinder Compatible List for the list of compatible grinders with a keyless gear case. Fig. B 16 5