Dirt Devil UD40140 Revision 1 (1/2006) - Page 6

LIGHTBULB: REMOVAL & REPLACEMENT TOOL REQUIRED: PHILLIPS OR FLATHEAD SCREWDRIVER WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK - UNPLUG CLEANER BEFORE REMOVING OR REPLACING LIGHTBULB. This cleaner uses a common automotive lamp #906, 13.0 volts. For bulb replacement, please visit our website at www.dirtdevil.com to buy online or locate a dealer nearest you. 1. 1a. 2. 3. Depress latch to remove dirt container from cleaner. Remove the two (2) screws located on the inside of the (Diagram 1). Remove lens (Diagram 1a). Pull bulb out of socket to remove. Do NOT twist. Gently push new bulb into socket to replace. Replace lens. Secure the headlight lens by replacing the two (2) screws. GENERAL MAINTENANCE WARNING: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS - UNPLUG BEFORE SERVICING. IF OBSTRUCTION DEVELOPS DURING FLOOR CLEANING: 1. If obstruction develops while cleaning carpets, turn cleaner OFF and unplug. Check to see if dirt container is full (Diagram 1); empty if needed (Page 9). 2. Check dirt path window and lower hose (Diagram 2). Remove any obstruction. 3. Turn cleaner over and remove nozzle guard (Diagram 3). Clear any obstruction that occurs in or around the brushroll area. IF OBSTRUCTION DEVELOPS DURING ABOVE FLOOR CLEANING: 1. If obstruction develops while above floor cleaning, turn cleaner OFF and unplug. Check to see if dirt container is full; empty if needed (Page 9). 2. Check airflow areas of hose (Diagram 4). If there is no suction, disconnect hose, drop quarter through end. If quarter comes out, there is NO blockage. 1. 2. 3. 4. TROUBLESHOOTING GUIDE WARNING: TO REDUCE RISK OF PERSONAL INJURY - UNPLUG CLEANER BEFORE SERVICING PROBLEM Cleaner won't run POSSIBLE REASON 1. Power cord not firmly plugged into outlet. 2. Blown fuse or tripped breaker. 3. Needs service. 4. Thermal Protector activated. POSSIBLE SOLUTION 1. Plug unit in firmly. 2. Check fuse or breaker in home. Replace fuse/reset breaker. 3. Take to service center. To find nearest location, visit our website at www.dirtdevil.com or call 1-800-321-1134. 4. Allow cleaner to cool - Pg. 3. Cleaner won't pick-up or low suction 1. Dirt container not installed correctly. 2. Dirt container full. 3. Brushroll worn. 4. Broken or worn belt. 5. Clogged filter. 6. Nozzle/dirt passage hose clogged. 1. Review dirt container removal & replacement Pg. 9. 2. Empty dirt container - Pg. 9. 3. Replace brushroll - Pg. 10. 4. Replace belt - Pg. 10. 5. Remove filter and clean - Pg. 9. 6. Remove lower hose; remove obstruction - Pg. 8. Dust escaping from cleaner 1. Dirt container full. 2. Dirt container not installed correctly. 3. Hose not connected correctly. 4. Filter not installed completely. 1. Empty dirt container - Pg. 9. 2. Review dirt container removal & replacement - Pg. 9. 3. Review hose installation - Pg. 7. 4. Review filter removal & replacement - Pg. 9. Cleaner tools won't pick-up 1. Hose clogged. 2. Dirt container full. 3. Filter clogged. 1. Remove hose and tools; remove obstruction Pg. 8. 2. Empty dirt container - Pg. 9. 3. Clean filter - Pg. 9. Headlight not working 1. Bulb burnt out. 2. Loose electrical wires. 1. Replace bulb - Pg. 11. 2. Take to service center. To find nearest location, visit our website at www.dirtdevil.com or call 1-800-321-1134. ANY OTHER SERVICING SHOULD BE DONE BY AN AUTHORIZED SERVICE REPRESENTATIVE CUSTOMER SERVICE (1-800-321-1134) In the event that further assistance is required, see your Yellow Pages for an authorized Royal® Dealer or visit our website at www.dirtdevil.com. Costs of any transportation to and from any place of repair are to be paid by the owner. The service parts used in this unit are easily replaced and readily available from an authorized Royal® Dealer or retailer. Always identify your cleaner by the model number and manufacturing code when requesting information or ordering replacement parts. (The model number appears on the bottom of the cleaner.) 11 12