Dynex DX-L37-10A User Manual (English) - Page 13

Turning on your TV for the first, Understanding the basics

Get Dynex DX-L37-10A PDF manuals and user guides View all Dynex DX-L37-10A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

10 Turning on your TV for the first time Turning on your TV for the first time To configure your TV: 1 Make sure that you have inserted the batteries in the remote control, connected the antenna to the TV, and connect the AC power. 2 Press (Power), then wait several seconds. The initial Setup Wizard screen opens (only the first time you turn on your TV). 6 Press to highlight Air/Cable, then press or to select Air or Cable, depending on the type of antenna connection you have. 7 Press to highlight Auto Scan, then press ENTER or to automatically scan for available channels. 3 Press or to highlight Menu Language, then press or to select the menu language you want. 4 Press to highlight Time Zone, then press or to select your time zone. Auto Scan may take a while to complete. A progress report is displayed while your TV is scanning for available channels. You can press MENU to exit Auto Scan prior to completion, but you will need to run Auto Scan later to complete the process. Auto Scan creates a list of available/receivable channels for the selected signal input. 5 Press to highlight DST (Daylight Saving Time), then press or to select On (to automatically change the time for Daylight Saving Time), or Off (to ignore it or set it yourself ). Understanding the basics Turning your TV on or off To turn your TV on or off (standby mode): 1 Plug the power cord into an AC power outlet. 2 Press (power). Your TV turns on. 3 Press again to turn off your TV. When you turn off your TV, it goes into standby mode. Warning: When your TV is in standby mode, it is still receiving power. To completely disconnect power, unplug the power cord. Note: If your TV does not receive an input signal for several minutes, it automatically goes into standby mode.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
10
Turning on your TV for the first time
Turning on your TV for the first
time
To configure your TV:
1
Make sure that you have inserted the batteries in the remote
control, connected the antenna to the TV, and connect the AC
power.
2
Press
(Power), then wait several seconds. The initial
Setup
Wizard
screen opens (only the first time you turn on your TV).
3
Press
or
to highlight
Menu Language
, then press
or
to select the menu language you want.
4
Press
to highlight
Time Zone
, then press
or
to select
your time zone.
5
Press
to highlight
DST
(Daylight Saving Time), then
press
or
to select
On
(to automatically change the time for
Daylight Saving Time), or
Off
(to ignore it or set it yourself ).
6
Press
to highlight
Air/Cable
, then press
or
to select
Air
or
Cable
, depending on the type of antenna connection you
have.
7
Press
to highlight
Auto Scan
, then press
ENTER
or
to
automatically scan for available channels.
Auto Scan may take a while to complete. A progress report is
displayed while your TV is scanning for available channels. You
can press
MENU
to exit Auto Scan prior to completion, but you
will need to run Auto Scan later to complete the process.
Auto Scan creates a list of available/receivable channels for the
selected signal input.
Understanding the basics
Turning your TV on or off
To turn your TV on or off (standby mode):
1
Plug the power cord into an AC power outlet.
2
Press
(power). Your TV turns on.
3
Press
again to turn off your TV. When you turn off your TV, it
goes into standby mode.
Warning:
When your TV is in standby mode, it is still receiving power. To
completely disconnect power, unplug the power cord.
Note:
If your TV does not receive an input signal for several minutes, it
automatically goes into standby mode.