Edimax BR-6624 Manual - Page 10

Rear Panel - default ip

Get Edimax BR-6624 PDF manuals and user guides View all Edimax BR-6624 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Rear Panel DC 5V WAN 2 Reset Button LAN Ports WAN 1 Figure 1-2: Rear Panel Connect the supplied power adapter here. Connect the 2nd Broadband Modem here, if available. When pressed and released, The Load Balancer will reboot (restart) within 1 second. It resets to default over 3 seconds. Connect the PCs to these ports. Both 10BaseT and 100BaseT connections can be used simultaneously. Note: Any port will automatically operate as an "Uplink" port if required. Just use a normal LAN cable to connect to a normal port on another hub. Connect the primary Broadband Modem here. Default Settings When The Load Balancer has finished booting, all configuration settings will be set to the factory defaults, including: • IP Address set to its default value of 192.168.1.1, with a Network Mask of 255.255.255.0 • DHCP Server is enabled • User Name: admin • Password cleared (no password) TFTP Download This setting should be used only if your Load Balancer is unusable, and you wish to restore it by downloading new firmware. Follow this procedure: 1. Power On The Load Balancer. 2. Use the supplied Windows utility or a TFTP client program applies the new firmware. If using the supplied Windows TFTP program, the screen will look like the following example. Page 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
Page 6
Rear Panel
Figure 1-2: Rear Panel
DC 5V
Connect the supplied power adapter here.
WAN 2
Connect the 2
nd
Broadband Modem here, if available.
Reset Button
When pressed and released, The Load Balancer will reboot (restart) within 1
second. It resets to default over 3 seconds.
LAN Ports
Connect the PCs to these ports. Both 10BaseT and 100BaseT connections can
be used simultaneously.
Note:
Any port will automatically operate as an "Uplink" port if required. Just use a
normal LAN cable to connect to a normal port on another hub.
WAN 1
Connect the primary Broadband Modem here.
Default Settings
When The Load Balancer has finished booting, all configuration settings will be set to the factory
defaults, including:
•
IP Address
set to its default value of 192.168.1.1, with a
Network Mask
of 255.255.255.0
•
DHCP Server
is enabled
•
User Name: admin
•
Password cleared (no password)
TFTP Download
This setting should be used only if your Load Balancer is unusable, and you wish to restore it by
downloading new firmware. Follow this procedure:
1. Power On The Load Balancer.
2.
Use the supplied Windows utility or a TFTP client program applies the new firmware. If using the
supplied Windows TFTP program, the screen will look like the following example.