Epson EMP S5 User Guide - Page 53

Warning, Caution, How to replace the lamp

Get Epson EMP S5 - SVGA LCD Projector PDF manuals and user guides
UPC - 010343864054
View all Epson EMP S5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Replacing Consumables f How to replace the lamp Warning • When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. If replacing the lamp of a projector which has been installed on the ceiling, you should always assume that the lamp is broken, and you should stand to the side of the lamp cover, not underneath it. Remove the lamp cover gently. Small pieces of glass may fall out when the lamp cover is opened. If pieces of glass get into your eyes or mouth, seek medical advice immediately. Caution • When replacing the lamp because it has stopped illuminating, there is a possibility that the lamp may be broken. Wait until the lamp has cooled down sufficiently before removing the lamp cover. If the lamp is still hot, burns or other injuries may result. It takes about one hour after the power has been turned off for the lamp to be cool enough. 53 Procedure A After you turn off the projector's power and the confirmation buzzer beeps twice, disconnect the power cable. B Wait until the lamp has cooled down, then remove the lamp cover. Loosen the lamp cover fixing screw with the screwdriver supplied with the new lamp or a + head screwdriver. Then slide the lamp cover straight forward and lift it to remove.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Replacing Consumables
53
f
How to replace the lamp
A
After you turn off the projector's power and the
confirmation buzzer beeps twice, disconnect the
power cable.
B
Wait until the lamp has cooled down, then remove
the lamp cover.
Loosen the lamp cover fixing screw with the screwdriver supplied
with the new lamp or a + head screwdriver. Then slide the lamp
cover straight forward and lift it to remove.
Warning
• When replacing the lamp because it has stopped illuminating,
there is a possibility that the lamp may be broken.
If replacing the lamp of a projector which has been installed on
the ceiling, you should always assume that the lamp is broken,
and you should stand to the side of the lamp cover, not underneath
it. Remove the lamp cover gently. Small pieces of glass may fall
out when the lamp cover is opened. If pieces of glass get into your
eyes or mouth, seek medical advice immediately.
Caution
• When replacing the lamp because it has stopped illuminating,
there is a possibility that the lamp may be broken.
Wait until the lamp has cooled down sufficiently before removing
the lamp cover. If the lamp is still hot, burns or other injuries may
result. It takes about one hour after the power has been turned off
for the lamp to be cool enough.
Procedure