Epson PowerLite 715c User Manual - Page 96

warning, Maintaining and Transporting the Projector

Get Epson PowerLite 715c PDF manuals and user guides View all Epson PowerLite 715c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

Follow these steps to replace the lamp: 1. Turn off the projector, then unplug the power cord. 2. Allow the projector to cool down for at least an hour (if it has been on). 3. Turn the projector upside-down to access the lamp compartment. 4. Use a screwdriver to loosen the retaining screw on the lamp cover. (You can't remove the screw from the cover.) When the screw is loose, lift off the lamp cover. ) warning Let the lamp cool before replacing it. If the lamp breaks, handle the shards carefully to avoid injury. 5. Use a screwdriver to loosen the two screws holding the lamp in place. (You can't remove these screws.) 6. Lift up the wire handle, as shown, and pull the lamp straight out. handle Maintaining and Transporting the Projector 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Maintaining and Transporting the Projector
87
Follow these steps to replace the lamp:
1.
Turn off the projector, then unplug the power cord.
2.
Allow the projector to cool down for at least an hour (if it has
been on).
3.
Turn the projector upside-down to access the lamp compartment.
4.
Use a screwdriver to loosen the retaining screw on the lamp cover.
(You can
’
t remove the screw from the cover.)
When the screw is loose, lift off the lamp cover.
)
5.
Use a screwdriver to loosen the two screws holding the lamp in
place. (You can
’
t remove these screws.)
6.
Lift up the wire handle, as shown, and pull the lamp straight out.
warning
Let the lamp cool before
replacing it. If the lamp
breaks, handle the shards
carefully to avoid injury.
handle