Epson PowerLite 81p Product Information Guide - Page 12

Replacing the Lamp - parts

Get Epson PowerLite 81p PDF manuals and user guides View all Epson PowerLite 81p manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Epson PowerLite 61p/81p Projector 3. Turn the projector upside-down and clean the filter and air intake vents on the base of the projector. Air vent Air vent Air filter If dirt is difficult to remove or the filter is torn, replace it. The air filter set (part number V13H134A06) contains two filters. Contact your dealer or call Epson at (800) 873-7766 to obtain a new set. In Canada, please call (800) 463-7766 to locate a dealer. Note: When you get a replacement lamp for your projector, a new air filter is included. Replace the filter when you replace the lamp. 4. If you need to replace the filter, slide it off as shown. 5. Align the new filter carefully as you slide it in until it clicks into place. Replacing the Lamp The projection lamp typically lasts for about 2000 hours of use (in high brightness mode) or 3000 hours (in low brightness mode). It is time to replace the lamp when: ❏ The projected image gets darker or starts to deteriorate. ❏ The warning light is flashing orange. ❏ The message Replace the Lamp appears on the screen when the lamp comes on. To maintain brightness and image quality, replace the lamp as soon as possible. Note: You can check how many hours the lamp has been used in the Info menu. Note: Turn the projector off when not in use. Coninuous use may reduce the overall life of the product. Contact your dealer or call Epson at (800) 873-7766 in the United States for a replacement lamp. Request part number V13H010L30. In Canada, please call (800) 463-7766 to locate a dealer. Follow these steps to replace the lamp: 1. Press the P Power button twice to turn off the projector. When you hear the projector beep twice, unplug the power cord. 2. If the projector has been on, allow it to cool down for at least half an hour (or until the lamp is cool). Warning: Let the lamp cool before replacing it. If the lamp breaks, handle the shards carefully to avoid injury. 3. Use the screwdriver included with the replacement lamp to loosen the screw holding the lamp cover (located on top of the projector). 4. Slide the cover out, then lift it off. 12 - Epson PowerLite 61p/81p Projector 6/04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
Epson PowerLite 61p/81p Projector
12
-
Epson PowerLite 61p/81p Projector
6
/04
3.
Turn the projector upside-down and clean the filter and air
intake vents on the base of the projector.
If dirt is difficult to remove or the filter is torn, replace it.
The air filter set (part number V13H134A06) contains two
filters. Contact your dealer or call Epson at (800) 873-7766
to obtain a new set. In Canada, please call (800) 463-7766 to
locate a dealer.
Note:
When you get a replacement lamp for your projector, a new air
filter is included. Replace the filter when you replace the lamp.
4.
If you need to replace the filter, slide it off as shown.
5.
Align the new filter carefully as you slide it in until it clicks
into place.
Replacing the Lamp
The projection lamp typically lasts for about 2000 hours of use
(in high brightness mode) or 3000 hours (in low brightness
mode). It is time to replace the lamp when:
The projected image gets darker or starts to deteriorate.
The
warning light is flashing orange.
The message
Replace the Lamp
appears on the screen when
the lamp comes on. To maintain brightness and image
quality, replace the lamp as soon as possible.
Note:
You can check how many hours the lamp has been used in the Info
menu.
Note:
Turn the projector off when not in use. Coninuous use may reduce
the overall life of the product.
Contact your dealer or call Epson at (800) 873-7766 in the
United States for a replacement lamp. Request part number
V13H010L30
. In Canada, please call (800) 463-7766 to locate a
dealer.
Follow these steps to replace the lamp:
1.
Press the
P
Power
button twice to turn off the projector.
When you hear the projector beep twice, unplug the power
cord.
2.
If the projector has been on, allow it to cool down for at least
half an hour (or until the lamp is cool).
Warning:
Let the lamp cool before replacing it. If the lamp breaks, handle
the shards carefully to avoid injury.
3.
Use the screwdriver included with the replacement lamp to
loosen the screw holding the lamp cover (located on top of
the projector).
4.
Slide the cover out, then lift it off.
Air vent
Air filter
Air vent