Epson Stylus Pro WT7900 Designer Edition User's Guide - Page 17

Chap 1-Setting Up the Printer, Unpacking and Assembling the Printer

Get Epson Stylus Pro WT7900 Designer Edition PDF manuals and user guides View all Epson Stylus Pro WT7900 Designer Edition manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

17 Chapter 1: Setting Up the Printer This chapter includes the following information: • Unpacking and assembling the Epson Stylus Pro WT7900 • Connecting the power cord • Installing ink • Connecting to your computer and a network • Installing the printer software • Updating the printer firmware • Configuring the printer for a network Unpacking and Assembling the Printer WARNING: Four people are required to unpack and set up the printer. Note: When choosing a place for the printer, leave adequate room for easy access and ventilation. Avoid locations subject to direct sunlight, excessive heat, moisture, or dust. Also avoid locations near potential sources of electromagnetic interference, such as loudspeakers, cordless phones, TVs, or air conditioners. Before you begin, make sure you have sufficient space to set up and use the printer-at least 12 inches (300 mm) on all sides in addition to these dimensions: • 53 × 26 inches (1356 × 667 mm) without the film basket installed • 53 × 57 inches (1356 × 1442 mm) with the film basket installed For assembly, you need floor space of approximately 8 × 8 feet (2.4 × 2.4 m) for the printer and stand. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
17
17
This chapter includes the following information:
•
Unpacking and assembling the Epson Stylus Pro WT7900
•
Connecting the power cord
•
Installing ink
•
Connecting to your computer and a network
•
Installing the printer software
•
Updating the printer firmware
•
Configuring the printer for a network
Unpacking and Assembling the Printer
Before you begin, make sure you have sufficient space to set up and use the
printer—at least 12 inches (300 mm) on all sides in addition to these
dimensions:
•
53 × 26 inches (1356 × 667 mm) without the film basket installed
•
53 × 57 inches (1356 × 1442 mm) with the film basket installed
For assembly, you need floor space of approximately 8 × 8 feet (2.4 × 2.4 m)
for the printer and stand.
Chapter 1:
Setting Up
the Printer
WARNING:
Four people are
required to unpack and set
up the printer.
Note:
When choosing a
place for the printer, leave
adequate room for easy
access and ventilation.
Avoid locations subject to
direct sunlight, excessive
heat, moisture, or dust.
Also avoid locations near
potential sources of
electromagnetic
interference, such as
loudspeakers, cordless
phones, TVs, or air
conditioners.