Fender Hot Rod DeVilletrade III 212 Owners Manual - Page 8
Rear Panel, Specifications
View all Fender Hot Rod DeVilletrade III 212 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
Rear Panel T. POWER CORD - Connect to a grounded outlet in accordance with the voltage and frequency ratings specified on the rear panel of your amplifier. U. FUSE - The fuse protects the unit from electrical faults. Replace fuses only with the type and rating specified on the fuse holder. If the unit repeatedly blows fuses, have the unit tested at an authorized Fender® Service Center. V. MAIN SPEAKER JACK - One of the following speaker configurations (internal or external) must always be connected when the unit is ON to prevent damage to the amplifier: DeVille™ 410 / Deluxe™ DeVille™ 212 1. 1. 2. 2. 3.* 3.* 2 *Insert an open plug (without speakers connected) into the Main Speaker jack {V} for configuration three (3). W. EXTERNAL SPEAKER JACK - This jack is wired in parallel with the main speaker jack and must only be used with a speaker load or an open plug connected to the main speaker jack, as shown above in the MAIN SPEAKER JACK diagram. X. FENDER® GROOVE TUBES® GT6L6B - Your new Fender amplifier comes equipped with the highest quality tubes available, sourced from various manufacturers worldwide. Because of occasional irregularities in supply, the specific tube type used in each amplifier is subject to change without notice. When replacing output tubes, please note the specific tube markings on the original tubes factory supplied with your amplifier. For example, 6L6 output tube types used by Fender include, but are not limited to: 6L6GC; 6L6WXT; 6L6C; 6L6GE; etc. The installation of a different type may require significant adjustment by a qualified technician to avoid reduction in performance and tube life. Additionally, Groove Tubes® tests and sorts many of our output tubes based on their measured performance. The sorted tubes are marked with a label on the base with coarse ratings of BLUE, WHITE, & RED plus fine ratings of 1-10. If your amp came supplied with, for example, a pair of matched GT-6L6-GE power tubes ranked at WHITE-6, then any pair of GT-6L6-GE power tubes marked with a course rating of WHITE will be a good replacement. If the tube replacements are marked as WHITE-6, they will be a perfect direct replacement. If you have questions or concerns, contact your Fender dealer or authorized service center. Y. PREAMP TUBE STABILIZER - A vibration-absorbing stabilizer is installed around the preamp tubes to minimize the tube microphonics that normally develop over time. The stabilizer can be used with all preamp tubes compatible with your Hot Rod amplifier. Specifications TYPE: PART NUMBERS: POWER REQUIREMENT / POWER OUTPUT: INPUT 1 / INPUT 2 IMPEDANCES: PREAMP OUTPUT IMPEDANCE: POWER AMP INPUT IMPEDANCE / SENSITIVITY: TUBES: *(Tube label color: Red=1, White=2, Blue=3) FUSE: SPEAKERS: FOOTSWITCH: DIMENSIONS WEIGHT: HEIGHT: WIDTH: DEPTH: DEVILLE 410 DEVILLE 212 PR 1110 PR 1123 2230100000 (120V, 60Hz) 2230000000 (120V, 60Hz) 2230101000 (110V, 60Hz) TW 2230001000 (110V, 60Hz) TW 2230103000 (240V, 50Hz) AUS 2230003000 (240V, 50Hz) AUS 2230104000 (230V, 50Hz) UK 2230004000 (230V, 50Hz) UK 2230105000 (220V, 50Hz) ARG 2230005000 (220V, 50Hz) ARG 2230106000 (230V, 50Hz) EUR 2230006000 (230V, 50Hz) EUR 2230107000(100V, 50/60Hz) JPN 2230007000 (100V, 50/60Hz) JPN 2230109000 (220V, 60Hz) ROK 2230009000 (220V, 60Hz) ROK 180W / 60W into 8Ω or 4Ω at 5% THD 180W / 60W into 4Ω or 2Ω at 5% THD 1MΩ / 136kΩ 1MΩ / 136kΩ 1.5kΩ max 1.5kΩ max 200 mV for clipping / 54kΩ 200 mV for clipping / 54kΩ 3 Fender Groove Tubes GT12AX7 (099-4005-000) 3 Fender Groove Tubes GT12AX7 (099-4005-000) 2 Fender Groove Tubes GT6L6B (099-4401-*02) 2 Fender Groove Tubes GT6L6B (099-4401-*02) 3AL, 250V fuse (100V-120V versions) 3AL, 250V fuse (100V-120V versions) 1.6AL, 250V fuse (220V-240V versions) 1.6AL, 250V fuse (220V-240V versions) 4 10" 8Ω Fender Model V 1030 Special Design (048332) 2 12" 8Ω Celestion G12-P80 (076501) 2 button, Gain/Channel (079606) 2 button, Gain/Channel (079606) 23.5 in (59.7 cm) 21 in (53.3 cm) 23.5 in (59.7 cm) 24.25 in (61.6 cm) 10.75 in (27.3 cm) 10.75 in (27.3 cm) 50 lb (22.7 kg) 53.5 lb (24.3 kg) Product specifications are subject to change without notice. 8 f e n d e r. c o m DELUXE PR 1110 2230200000 (120V, 60Hz) 2230201000 (110V, 60Hz) TW 2230203000 (240V, 50Hz) AUS 2230204000 (230V, 50Hz) UK 2230205000 (220V, 50Hz) ARG 2230206000 (230V, 50Hz) EUR 2230207000 (100V, 50/60Hz) JPN 2230209000 (220V, 60Hz) ROK 180W / 40W into 4Ω or 2Ω at 5% THD 1MΩ / 136kΩ 1.5kΩ max 200 mV for clipping / 54kΩ 3 Fender Groove Tubes GT12AX7 (099-4005-000) 2 Fender Groove Tubes GT6L6B (099-4401-*02) 3AL, 250V fuse (100V-120V versions) 1.6AL, 250V fuse (220V-240V versions) 1 12" 8Ω Celestion G12-P80 (076501) 2 button, Gain/Channel (079606) 18.75 in (47.6 cm) 23.5 in (59.7 cm) 10.5 in (26.7 cm) 49.5 lb (22.5 kg)