Fluke 744 Fluke 744 Users Manual - Page 27

Display, Range Status: Shows whether Auto Range is - parts

Get Fluke 744 PDF manuals and user guides View all Fluke 744 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Display Figure 7 shows the features of a typical display. The display shown is MEASURE mode. Near the top of the display is "Source Off." This is the area of the display that shows what is happening in the other mode (SOURCE or MEASURE). The other parts of the display are as follows: • Status Bar: shows the time and date (if set in Setup mode), and shows the status of Loop Power, Battery Save, and Backlight Timeout; all of which are set in Setup mode. The low battery and backlight on symbols also appear here. • Mode Indicator: Shows whether the calibrator is in MEASURE or SOURCE mode. In split screen MEASURE/SOURCE mode, there is a Mode Indicator for each window. Documenting Process Calibrator Operating Features • Measured Value: Shows the measured value in your choice of engineering units or percent of scale. • Range Status: Shows whether Auto Range is on, and what range is currently being used. • Custom Units Indicator: Shows that the displayed units are custom. The original engineering units of the measure or source function are not displayed. • Secondary Value: Shows the measure or source value in original engineering units whenever scaling or custom units are active. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
Documenting Process Calibrator
Operating Features
17
Display
Figure 7 shows the features of a typical display. The
display shown is MEASURE mode. Near the top of
the display is “Source Off.” This is the area of the
display that shows what is happening in the other
mode (SOURCE or MEASURE). The other parts of
the display are as follows:
•
Status Bar: shows the time and date (if set in
Setup mode), and shows the status of Loop
Power, Battery Save, and Backlight Timeout; all
of which are set in Setup mode. The low battery
and backlight on symbols also appear here.
•
Mode Indicator: Shows whether the calibrator is
in MEASURE or SOURCE mode. In split screen
MEASURE/SOURCE mode, there is a Mode
Indicator for each window.
•
Measured Value: Shows the measured value in
your choice of engineering units or percent of
scale.
•
Range Status: Shows whether Auto Range is on,
and what range is currently being used.
•
Custom Units Indicator: Shows that the displayed
units are custom. The original engineering units
of the measure or source function are not
displayed.
•
Secondary Value: Shows the measure or source
value in original engineering units whenever
scaling or custom units are active.