Home » Fluke Manuals » Electronics Accessories » Fluke P3011-MMHG » Manual Viewer

Fluke P3011-MMHG Product Manual - Page 40

Ancillary Equipment, Dirt/Moisture Trap, P5531

Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Chapter 8 Ancillary Equipment Dirt/Moisture Trap, P5531 If there is any doubt that the instrument to be tested is not internally clean, then the addition of the P5531 Dirt/Moisture Trap will protect the deadweight tester from contamination and possible damage. Any particles or moisture present within the DUT will fall into the clear, acrylic chamber, where they can be seen by the operator. The top connection reproduces the test port on the deadweight tester, allowing the standard gauge adapters to be used. Figure 8-1. Dirt/Moisture Trap gjn030.bmp 8-1 MyFlukeStore Shop for Fluke products online at: www. .com 1.888.610.7664

Section	Page
P3000 Series Users Manual	1
LIMITED WARRANTY AND LIMITATION OF LIABILITY	2
Table of Contents	3
List of Tables	5
List of Figures	6
1. General Information	7
Introduction	7
How to Contact Fluke	7
Safety Information	7
Safety Summary	7
Compressed Gas	8
Heavy Weights	8
Personal Protective Equipment	8
Symbols Used in this Manual	8
Operating Principle	8
Operating & Storage Specification	9
Environmental Corrections	9
Gravity	9
Temperature	9
Model Variations	10
2. Preparation	14
Introduction	14
Connection to External Pressure/Vacuum Supplies	14
Connections	15
Test Port Insert	18
3. Operation	19
Introduction	19
Single PCU Models — Pressure	19
Single PCU Models — Vacuum	20
Dual PCU (Pressure & Vacuum) Models	20
4. Calibration in Different Pressure Units	22
Introduction	22
Conversion Weights	22
Software	22
5. Maintenance & Servicing	23
Introduction	23
PCU Assembly — 10 mm Nominal Diameter — Pressure	23
Piston Disassembly	23
Piston Cleaning	23
Piston Re-Assembly	24
Replacement PCU Assembly	24
PCU Assembly — 10 mm Nominal Diameter — Vacuum	25
Piston Disassembly	25
Piston Cleaning	25
Piston Re-Assembly	26
Replacement PCU Assembly	26
PCU Assembly — 16 mm Nominal Diameter	27
Piston Disassembly	27
Piston Cleaning	27
Piston Re-Assembly	28
Replacement PCU Assembly	28
PCU Assembly — 22 mm Nominal Diameter	29
Piston Cleaning	29
Piston Re-Assembly	30
Replacement PCU Assembly	30
Top Plate Removal	31
Handpump Assembly	32
Disassembly	32
Cleaning and Inspection	32
Re-Assembly	32
System Selector Valve	34
Disassembly	34
Cleaning & Inspection	34
Re-Assembly	34
Safety Valve	35
Disassembly	35
Re-Assembly	35
6. Fault Finding	37
Poor PCU Spin/Sensitivity	37
System Will Not Pressurize	37
High PCU Fall-Rate	38
Handpump Malfunction	38
7. Storage & Transportation	39
Instrument	39
Weights	39
8. Ancillary Equipment	40
Dirt/Moisture Trap, P5531	40
Angle Adapter, P5543	41

Match case Limit results 1 per page

8-1

Chapter 8

Ancillary Equipment

Dirt/Moisture Trap, P5531

If there is any doubt that the instrument to be tested is not internally clean, then the

addition of the P5531 Dirt/Moisture Trap will protect the deadweight tester from

contamination and possible damage. Any particles or moisture present within the DUT

will fall into the clear, acrylic chamber, where they can be seen by the operator.

The top connection reproduces the test port on the deadweight tester, allowing the

standard gauge adapters to be used.

gjn030.bmp

Figure 8-1. Dirt/Moisture Trap

Shop for Fluke products online at:

1.888.610.7664

www.

MyFlukeStore

.com