Home » Frigidaire Manuals » Ranges » Frigidaire FPEF3077QF » Manual Viewer

Frigidaire FPEF3077QF Complete Owner's Guide - Page 13

Bridge Element

View all Frigidaire FPEF3077QF manuals

Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Bridge Element On the left side of the cooktop there are two single burners with a bridge element between them. When turned on, the bridge element allows for a larger cooking area by cycling at the same temperature as the left rear element. For the bridge to be operational, the left rear burner must be on. When the left front burner is also on the entire left side of the cooktop can accommodate specialized cookware. To operate the bridge element: 1. Turn on the left rear element to the desired level of heat. 2. Turn the bridge control to the on position. 3. The bridge element will heat at the same level as the left rear element. If the left rear control is turned off, the bridge will also turn off. Be sure to turn the bridge control to the off position when finished cooking. BRIDGE SETTING SURFACE CONTROLS Figure 6: Bridge element control CAUTION Use only cookware specifically designed for use with the bridge element. 13

Section	Page
Product Record and Registration	2
Important Safety Instructions	3
Before Setting Surface Controls	8
Setting Surface Controls	11
Before Setting Oven Controls	14
Setting Oven Controls	15
Cleaning Various Parts of Your Oven	30
Cooktop Maintenance	31
Figure 36: Cooktop care	31
Cooktop Cleaning	31
Figure 37: Cooktop cleaning	31
Cooktop Maintenance (cont’d)	32
Figure 38: Cleaning products to avoid	32
Removing and Replacing the Oven Door	33
1. Open oven door completely, horizontal with floor (See Figure 39).	33
2. Pull the door hinge locks on both left and right door hinges down from the oven frame completely towards the oven door (See Figure 40). A tool such as a small flat-blade screwdriver may be required.	33
3. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 41).	33
4. Close the door to approximately 10 degrees from the door frame (See Figure 41).	33
5. Lift the oven door hinge arms over the roller pins located on each side of the oven frame (See Figure 42).	33
1. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 41).	33
2. Holding the oven door at the same angle as the removal position, seat the hook of the hinge arm over the roller pins located on each side of the oven door frame (See Figure 41 and Figure 42). The hook of the hinge arms must be fully seated onto th...	33
3. Fully open the oven door, horizontal with floor (See Figure 39).	33
4. Push the door hinge locks up towards and into the oven frame on both left and right oven door hinges to the locked position (See Figure 40).	33
5. Close the oven door.	33
Figure 39: Door hinge location	33
Figure 40: Door hinge locks	33
Figure 41: Holding door for removal	33
Figure 42: Replacement and location of hinge arm and roller pin	33
Replacing the Oven Light	34
1. Turn electrical power off at the main source or unplug the appliance.	34
2. Remove interior oven light shield after removing the wire holder by carefully moving the wire to the side of the glass shield. The tension from the wire holds the glass shield in place.	34
3. Pull the shield straight out. Do not twist or turn.	34
4. Replace bulb with a new appliance bulb.	34
5. Replace glass oven light shield. Replace wire holder.	34
6. Turn power back on again at the main source (or plug the appliance back in).	34
7. Be sure to reset the time of day on the clock.	34
Figure 43: Oven light protected by glass shield	34
Before You Call	35