Frigidaire FPEF3077QF Complete Owner's Guide - Page 26

26

SETTING OVEN CONTROLS

Adjusting the Oven Temperature

The temperature in the oven is pre-set at the factory. When

first using the oven, be sure to follow recipe times and

temperatures.

If you think the oven is cooking too hot or too cool for the

temperature you select, you can adjust the actual oven

temperature to be more or less than what is displayed by

accessing the UPO (User Programmable Offset).

Before adjusting, test a recipe by using a temperature

setting higher or lower than the recommended temperature.

The baking results should help you to decide how much of

an adjustment is needed.

Important:

Before making a temperature adjustment, make

sure both the oven mode and oven temperature control

knobs are in the OFF position.

To adjust the oven temperature:

1.

When the oven is idle, press and hold both the light icon

and the clock icon at the same time for a few seconds

until the display sounds an acceptance chime.

AUd

should appear in the display.

2.

Press the

+

key in the upper part of the display until

UPO

appears and the default setting of

0°

(or the last

offset temperature) is showing.

3.

Using the

+

or

-

key in the bottom of the display, press

until the desired temperature change (offset) is

reached. The display will change

±

5°

with each key

press to a maximum of

+ 35°

or a minimum of

– 35°F.

If a lower temperature offset is desired, press the

–

key in

the bottom of the display until the desired lower tempera-

ture appears.

Once the new offset appears in the display, release the key

and the control will accept the change.

4.

To return the display to normal, press and hold both the

oven

light

icon and the

clock

icon at the same time

until an acceptance chime sounds. The display will

return to show the time of day.

Do not use oven thermometers such as those found in

grocery stores to check the temperature settings inside

your oven. These oven thermometers may vary as much

as 20 to 40 degrees from actual temperatures.

Figure 24:

UPO shown at default setting

NOTE

Figure 25:

UPO shown 10° higher than default

Figure 26:

UPO shown 10° lower than default

Changing the UPO will not affect the broil or self clean

temperatures.

NOTE

Section	Page
Product Record and Registration	2
Important Safety Instructions	3
Before Setting Surface Controls	8
Setting Surface Controls	11
Before Setting Oven Controls	14
Setting Oven Controls	15
Cleaning Various Parts of Your Oven	30
Cooktop Maintenance	31
Figure 36: Cooktop care	31
Cooktop Cleaning	31
Figure 37: Cooktop cleaning	31
Cooktop Maintenance (cont’d)	32
Figure 38: Cleaning products to avoid	32
Removing and Replacing the Oven Door	33
1. Open oven door completely, horizontal with floor (See Figure 39).	33
2. Pull the door hinge locks on both left and right door hinges down from the oven frame completely towards the oven door (See Figure 40). A tool such as a small flat-blade screwdriver may be required.	33
3. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 41).	33
4. Close the door to approximately 10 degrees from the door frame (See Figure 41).	33
5. Lift the oven door hinge arms over the roller pins located on each side of the oven frame (See Figure 42).	33
1. Firmly grasp both sides of oven door along the door sides. Do not use the oven door handle (See Figure 41).	33
2. Holding the oven door at the same angle as the removal position, seat the hook of the hinge arm over the roller pins located on each side of the oven door frame (See Figure 41 and Figure 42). The hook of the hinge arms must be fully seated onto th...	33
3. Fully open the oven door, horizontal with floor (See Figure 39).	33
4. Push the door hinge locks up towards and into the oven frame on both left and right oven door hinges to the locked position (See Figure 40).	33
5. Close the oven door.	33
Figure 39: Door hinge location	33
Figure 40: Door hinge locks	33
Figure 41: Holding door for removal	33
Figure 42: Replacement and location of hinge arm and roller pin	33
Replacing the Oven Light	34
1. Turn electrical power off at the main source or unplug the appliance.	34
2. Remove interior oven light shield after removing the wire holder by carefully moving the wire to the side of the glass shield. The tension from the wire holds the glass shield in place.	34
3. Pull the shield straight out. Do not twist or turn.	34
4. Replace bulb with a new appliance bulb.	34
5. Replace glass oven light shield. Replace wire holder.	34
6. Turn power back on again at the main source (or plug the appliance back in).	34
7. Be sure to reset the time of day on the clock.	34
Figure 43: Oven light protected by glass shield	34
Before You Call	35

Frigidaire FPEF3077QF Complete Owner's Guide - Page 26

Adjusting the Oven Temperature

Page 26 highlights