Fujitsu MAP3367NC Manual/User Guide - Page 94

Refer to of SCSI Logical Interface Specifications for further details., the system

Get Fujitsu MAP3367NC - Enterprise 36.7 GB Hard Drive PDF manuals and user guides
UPC - 000004119623
View all Fujitsu MAP3367NC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

Notes: 1. The user can arbitrarily specify the following parameters according to the system requirements: • ARRE • AWRE • TB • PER 2. The user also can arbitrarily specify parameters other than the above. However, it is recommended to use the default setting in normal operations. (2) Disconnection/reconnection parameters (page code = 2) The following parameters are used to optimize the start timing of reconnection processing to transfer data on the SCSI bus at a read (READ or READ EXTENDED command) or write operation (WRITE, WRITE EXTENDED, or WRITE AND VERIFY command) of the disk. Refer to Chapter 2 of SCSI Logical Interface Specifications for further details. • Buffer full ratio • Buffer empty ratio Parameter Default value 00 (HEX) 00 (HEX) Notes: 1. In a system without the disconnection function, these parameters need not be specified. 2. Determine the parameter values in consideration of the following performance factors of the system: • Time required for reconnection processing • Average data transfer rate of the SCSI bus • Average amount of processing data specified with a command Refer to Chapter 2 of SCSI Logical Interface Specifications for how to obtain the rough calculation values for the parameter values to be set. It is recommended to evaluate the validity of the specified values by measuring performance in an operation status under the average system load requirements. 5-20 C141-E166

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
5-20
C141-E166
Notes:
1.
The user can arbitrarily specify the following parameters according to the system
requirements:
•
ARRE
•
AWRE
•
TB
•
PER
2.
The user also can arbitrarily specify parameters other than the above.
However, it is
recommended to use the default setting in normal operations.
(2)
Disconnection/reconnection parameters (page code = 2)
The following parameters are used to optimize the start timing of reconnection processing to
transfer data on the SCSI bus at a read (READ or READ EXTENDED command) or write
operation (WRITE, WRITE EXTENDED, or WRITE AND VERIFY command) of the disk.
Refer to Chapter 2 of SCSI Logical Interface Specifications for further details.
Parameter
Default value
• Buffer full ratio
00 (HEX)
• Buffer empty ratio
00 (HEX)
Notes:
1.
In a system without the disconnection function, these parameters need not be specified.
2.
Determine the parameter values in consideration of the following performance factors of
the system:
•
Time required for reconnection processing
•
Average data transfer rate of the SCSI bus
•
Average amount of processing data specified with a command
Refer to Chapter 2 of SCSI Logical Interface Specifications for how to obtain the rough
calculation values for the parameter values to be set.
It is recommended to evaluate the
validity of the specified values by measuring performance in an operation status under the
average system load requirements.