Fujitsu XG2600 Hardware Guide - Page 44

Connecting the Equipment, 2.3.1 Discharging Twisted Pair Cable

Get Fujitsu XG2600 PDF manuals and user guides View all Fujitsu XG2600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

XG2600 Hardware Guide Chapter 2 Installation 2.3 Connecting the Equipment We recommend discharging static electricity of twisted pair cable before connecting it to the switch. Also see below for how to install USB memory. 2.3.1 Discharging Twisted Pair Cable Discharge static electricity of the twisted pair cable through the ground wire cable (ground wire for power supply, buildings, etc.) using static electricity removal tool, before connecting twisted pair cable to the switch. Precautions • Unplug both ends of the twisted pair cable from equipments (HUB, router, and workstation) during discharging operation. • Do not use ground wire of electronic devices. Use grounded cable for power supply or buildings. • Do not short circuit with AC power supply when using ground wire for power suppl. 2.3.2 Cleaning SFP+ Module / Optical Connector When invisible small dust is adhered to SFP+ module /optical connector, optical signal will be shut or space caused by dust will impede transmission of optical signal. Therefore, clean up SFP+ module /optical connector before connection. Cleaning of SFP+ Module 1. Blow dust away with cleanly dry air or nitrogen. Check end face, and conduct operation below if dust is left. 2. Lightly dampen a cleaning stick (1.25mm across, for LC/MU) with isopropyl alcohol. After wiping off dust, slowly and carefully wipe off alcohol with a new and dry cleaning stick. 3. Insert a cleaning stick to the optical connector insertion part of SFP+ module, and slowly wheel it. SFP+ module cleaning stick 4. Insert and slowly wheel a new cleaning stick, and dry the SFP+ module. 5. Check if the dust is removed with 200-fold magnification fiber scope. 44 Connecting the Equipment

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
XG2600 Hardware Guide
Chapter 2 Installation
Connecting the Equipment
44
2.3
Connecting the Equipment
We recommend discharging static electricity of twisted pair cable before connecting it to the switch.
Also see below for how to install USB memory.
2.3.1
Discharging Twisted Pair Cable
Discharge static electricity of the twisted pair cable through the ground wire cable (ground wire for power supply,
buildings, etc.) using static electricity removal tool, before connecting twisted pair cable to the switch.
Precautions
•
Unplug both ends of the twisted pair cable from equipments (HUB, router, and workstation) during discharging
operation.
•
Do not use ground wire of electronic devices. Use grounded cable for power supply or buildings.
•
Do not short circuit with AC power supply when using ground wire for power suppl.
2.3.2
Cleaning SFP+ Module / Optical Connector
When invisible small dust is adhered to SFP+ module /optical connector, optical signal will be shut or space caused by dust will
impede transmission of optical signal.
Therefore, clean up SFP+ module /optical connector before connection.
Cleaning of SFP+ Module
1.
Blow dust away with cleanly dry air or nitrogen.
Check end face, and conduct operation below if dust is left.
2.
Lightly dampen a cleaning stick (1.25mm across, for LC/MU) with isopropyl alcohol. After wiping off
dust, slowly and carefully wipe off alcohol with a new and dry cleaning stick.
3.
Insert a cleaning stick to the optical connector insertion part of SFP+ module, and slowly wheel it.
4.
Insert and slowly wheel a new cleaning stick, and dry the SFP+ module.
5.
Check if the dust is removed with 200-fold magnification fiber scope.
SFP+ module
cleaning stick