GE JN328KSA Installation Instructions - Page 13

49-80589-6

13

INSTALLATION INSTRUCTIONS

Installation Instructions

11

MARK HOLES

Select the vent option that your installation will

require and proceed to that section:

A

Outside top exhaust

(Vertical duct–3-1/4" x 10" Rectangular)

Use the diagram or the hood as a template and

mark the locations on the cabinet for ductwork,

electrical wiring and keyhole screw slots.

B

Outside top exhaust

(Vertical duct–7" Round)




12

CUT HOLES

Cut holes at marked locations for duct and

electrical wiring. For the vertical duct, cut out

you can move the duct freely when installing

the hood. It may also ease installation by

13

RUN WIRES

Run the electrical wires through the wall or

cabinet according to National Electrical Code

and applicable local codes.

NOTE:

DO NOT turn the power on until

installation is complete.

C

Outside rear exhaust

(Horizontal duct–3-1/4" x 10" Rectangular)




D

Recirculating (non-vented ductless–

JN327, JN328 and RN328, and optional on

JV247, JV248, JV347, JV348, JV367 and

AV447 models only)

•

Use the hood as a template and mark the

locations on the cabinet for the electrical

wiring and keyhole screw slots.

•

Since the hood is to be recirculated (not to

be vented outside), do not cut out any vent

openings in the wall or cabinet bottom.

Hood mounting screws (4)

10

3

4

(24

hood)

13

3

4

(30

hood)

16

3

4

(36

hood)

10

3

4

(24

hood)

13

3

4

(30

hood)

16

3

4

(36

hood)

Cabinet front

Center

line

Electrical access

hole

(in cabinet bottom)

Wood shims

(recessed-

bottom cabinets only–shims

must be a minimum of 3/8

thick and cut to fit the width

of the inner recessed cabinet

bottom)

Access

hole for 7

round duct

9

5

8

1

3

8

1

1

4

7

3

4

5

3

4

Cabinet

bottom

8

DIA.

HOLE

Hood mounting

screws (4)

10

3

4

(24

hood)

13

3

4

(30

hood)

16

3

4

(36

hood)

10

3

4

(24

hood)

13

3

4

(30

hood)

16

3

4

(36

hood)

Cabinet front

Center

line

Electrical access hole

(in cabinet bottom)

Wood shims

(recessed-bottom

cabinets only–shims

must be a minimum

of 3/8

thick and cut

to fit the width of

the inner recessed

cabinet bottom)

9

5

8

1

3

8

1

1

4

7

3

4

3

3

4

1

2

5

1

4

5

1

4

Cabinet Bottom

Vertical duct

access hole

Wood shims

(recessed-bottom cabinets only–shims must be

a minimum of 3/8

thick and cut to fit the width

of the inner recessed cabinet bottom)

Cabinet front

Center line

Electrical access

hole

(in wall)

Hood mounting

screws (4)

Cabinet

bottom

10

3

4

(24

hood)

13

3

4

(30

hood)

16

3

4

(36

hood)

1

1

4

1

2

3

3

4

5

1

4

5

1

4

7

3

4

10

3

4

(24

hood)

13

3

4

(30

hood)

16

3

4

(36

hood)

Horizontal duct

access hole

GE JN328KSA Installation Instructions - Page 13

Mark Holes, Cut Holes, Run Wires

Page 13 highlights