Haier GDE950AW User Manual - Page 16

Gas Connections

Get Haier GDE950AW PDF manuals and user guides View all Haier GDE950AW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

English 4.  T hread a U.L. approved 30 Amp power cord. NEMA 14-30 type ST or SRDT through the strain relief. 5. A ttach the green power cord ground wire to the cabinet with green ground screw. 6.  A ttach the white (neutral) power cord conductors to the outer cord and the green ground wire from the dryer harness to the brass-colored center terminal on the terminal block. Tighten the screw securely. 7.  A ttach the red and black power cord conductors to the outer brass-colored terminals on the terminal block. Warning: Do not make a sharp bend or crimp the wiring /conductor at connections. 8. Tighten the screws securing the cord restraint firmly against the power cord. 9. Tighten the strain relief nut securely so that the strain relief does not turn. 10. Reinstall the terminal block cover.­ GAS CONNECTIONS GAS Dryer (GDG750AW and GDG950AW) NOTE: DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. Conversion Kit must be installed by a qualified gas technician. 1. Remove the shipping cap from gas pipe at the rear of the dryer. 2. Connect a 1/2 inch (1.27cm) I.D. semi-rigid or approved pipe from gas supply line to the 3/8 inch (0.96cm) pipe located on the back of the dryer. Use a 1/2 inch to 3/8 inch (1.27cm to 0.96cm) reducer for a connection. Apply an approved thread sealer that is resistant to the corrosive action of liquified gases on all pipe connections. 3. Open the shutoff valve in the gas supply line. 4. Test all connections by brushing on a soapy water solution. NEVER TEST FOR GAS LEAKS WITH AN OPEN FLAME. 5. Connect the exhaust duct to the outside exhaust system. Use duct tape to seal all joints. 6. With the dryer in its final position, adjust one or more of the legs until the dryer is resting solid on all four legs. Place a level on top of the dryer. THE DRYER MUST BE LEVEL AND RESTING SOLID ON ALL FOUR LEGS. 7. Plug the power AcoDrVdERinTtEoNaCIAgrounAdDeVdERoTuItSleStM. ENNOT TE: check to ensure power is OFF at circWuAitRbNreINaGker/fAuDseVEbRoTxENbCeIfAore plugging the power cord into the outlet. 8. Turn on the power at the circuit breaker/fuse box. CAUTION B efPoRreECoApUeCrIaÓtNing theATdTrEyNerT,IOmNake sure the dryer area is clean and free CAUTION fsreoemPRthcEaCotAmnUboCutIhsÓitinNbgle(smucaPhtReEarCisaAlbsU,oCxgIÓeasNs,oclilnoeth, iangnd, other flammable etc.) obstructs the vapors. flow of Also combustion and ventilation air through the louvered panel located on the rear of the dryer. 9. Run the dryer through a cycle check for proper operation. NOTE: On gas dryers, before the burner will light, it is necessary for the gas line to be bled of air. If the burner does not light within 45 seconds the first time the dryer is turned on, the safety switch will shut the burner off. If this happens, turn the dryer to "OFF" and wait 5 minutes before making another attempt to light. NOTE: Follow instructons supplied with kit. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
English
15
4.
Thread a U.L. approved 30 Amp power cord. NEMA 14-30 type ST or SRDT
through the strain relief.
5.
Attach the green power cord ground wire to the cabinet with green ground screw.
6.
Attach the white (neutral) power cord conductors to the outer cord and the
green ground wire from the dryer harness to the brass-colored center
terminal on the terminal block. Tighten the screw securely.
7.
Attach the red and black power cord conductors to the outer brass-colored terminals
on the terminal block.
Warning:
Do not make a sharp bend or crimp the wiring /conductor at
connections.
8. Tighten the screws securing the cord restraint firmly against the power cord.
9. Tighten the strain relief nut securely so that the strain relief does not turn.
10. Reinstall the terminal block cover.
NOTE: DO NOT connect the dryer to L.P. gas service without converting
the gas valve. An L.P. Conversion Kit must be installed by a
qualified gas technician.
1. Remove the shipping cap from gas pipe at the rear of the dryer.
2. Connect a 1/2 inch (1.27cm) I.D. semi-rigid or approved pipe from gas supply line to
the 3/8 inch (0.96cm) pipe located on the back of the dryer. Use a 1/2 inch to 3/8
inch (1.27cm to 0.96cm) reducer for a connection. Apply an approved thread sealer
that is resistant to the corrosive action of liquified gases on all pipe connections.
3. Open the shutoff valve in the gas supply line.
4. Test all connections by brushing on a soapy water solution.
NEVER TEST FOR GAS
LEAKS WITH AN OPEN FLAME.
5. Connect the exhaust duct to the outside exhaust system. Use duct tape to seal
all joints.
6. With the dryer in its final position, adjust one or more of the legs until the dryer is
resting solid on all four legs. Place a level on top of the dryer.
THE DRYER MUST
BE LEVEL AND RESTING SOLID ON ALL FOUR LEGS.
7. Plug the power cord into a grounded outlet.
NOTE:
check to ensure power is
OFF
at
circuit breaker/fuse box before plugging the power cord into the outlet.
8. Turn on the power at the circuit breaker/fuse box.
CAUTION
Before operating the dryer, make sure the dryer area is clean and free
from combustible materials, gasoline, and other flammable vapors. Also
see that nothing (such as boxes, clothing, etc.) obstructs the flow of
combustion and ventilation air through the louvered panel located on the
rear of the dryer.
9. Run the dryer through a cycle check for proper operation.
NOTE:
On gas dryers, before the burner will light, it is necessary for the gas line to be
bled of air. If the burner does not light within 45 seconds the first time the dryer
is turned on, the safety switch will shut the burner off. If this happens, turn the
dryer to “OFF” and wait 5 minutes before making another attempt to light.
NOTE:
Follow instructons supplied with kit.
GAS CONNECTIONS
GAS
Dryer
(GDG750AW and GDG950AW)