Haier GDE950AW User Manual - Page 6

Installation Instructions - washer

Get Haier GDE950AW PDF manuals and user guides View all Haier GDE950AW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

English ADVERTENCIA ADVERTISSMENT INWSATRNAINLGLAATDIVOERNTENICNIASTRUCTIONS CAUTION RisPkREoCAf UFCirIÓeN: ATTENTION CA UTION PR1EC.ACUlCoItÓheNs dryePrRiEnCsAtaUlClaIÓtioNn must be performed by a qualified installer. 2. Install the clothes dryer according to the manufacturer's instructions and local codes. 3. To reduce the risk of severe injury or death, follow all installation instructions. SAVE THESE INSTRUCTIONS Tools and materials required • Phillips-Head and flathead screwdrivers • Channel-lock adjustable pilers • 1/2-inch open-end wrench • Carpenter's level • Measuring tape (12ft. min.) • Duct tape • Pipe thread sealer (Gas) • Rigid or flexible metal 4 inch (102cm) duct • Vent hood Safety Warning: 1. Before starting installation, make sure that the gas shut off valve is in the off position. 2. All old gas connectors and gas piping should be discarded. ELECTRICAL REQUIREMENTS Electric Dryer: (GDE750AW and GDE950AW) Circuit Individual 30 Amp branch circuit fused with 30 Amp time-delay fuses or circuit breakers. Use seperately fused circuits for washers and dryers, and DO NOT operate a washer and dryer on the same circuit. Power Supply 3 or 4 wire, 240 Volt, 1 Phase, 60Hz, AC (Canada - 240 Volt, 1 Phase, 60 Hz, AC) Power Supply Cord Kit (Not supplied when sold in US. Must be purchased to meet local electrical codes.) The dryer MUST employ a 3-conductor power supply cord NEMA 10-30 Type SRDT rated at 240 Volt AC minimum, 30 Amp, with 3 open end spade lug connectors with 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
5
CAUTION
Risk of Fire:
1. Clothes dryer installation must be performed by a
qualified installer.
2. Install the clothes dryer according to the manufacturer’s
instructions and local codes.
3. To reduce the risk of severe injury or death, follow all installation
instructions.
SAVE THESE INSTRUCTIONS
Tools and materials required
•
Phillips-Head and flathead screwdrivers
•
Channel-lock adjustable pilers
•
1/2-inch open-end wrench
•
Carpenter’s level
•
Measuring tape (12ft. min.)
•
Duct tape
•
Pipe thread sealer (Gas)
•
Rigid or flexible metal 4 inch (102cm) duct
•
Vent hood
Safety Warning:
1. Before starting installation, make sure that the gas shut off valve is in the
off position.
2. All old gas connectors and gas piping should be discarded.
ELECTRICAL REQUIREMENTS
Electric Dryer:
(GDE750AW and GDE950AW)
Circuit
Individual 30 Amp branch circuit fused with 30 Amp time-delay fuses or circuit
breakers. Use seperately fused circuits for washers and dryers, and DO NOT operate
a washer and dryer on the same circuit.
Power Supply
3 or 4 wire, 240 Volt, 1 Phase, 60Hz, AC
(Canada - 240 Volt, 1 Phase, 60 Hz, AC)
Power Supply Cord Kit
(Not supplied when sold in US. Must be purchased to meet local electrical codes.)
The dryer MUST employ a 3-conductor power supply cord NEMA 10-30 Type SRDT
rated at 240 Volt AC minimum, 30 Amp, with 3 open end spade lug connectors with
INSTALLATION INSTRUCTIONS
English