Haier HDC2406TW HDC2406TW Manual - Page 18

Operating Instructions

Get Haier HDC2406TW PDF manuals and user guides View all Haier HDC2406TW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

English Operating Instructions Operating Your Dishwasher 1. Ensure that all electrical, water, and drain connections have been installed correctly before proceeding. 2. Load the dishwasher (See the "Loading your Dishwasher" section). 3. Make sure that the water supply is turned on to full pressure. 4. Add the appropriate amount of dishwasher detergent to the dispenser (see Proper Use of Detergent Section). 5. Close the door and ensure that the door latch has engaged. 6. Turn the dishwasher ON by pressing the ON / OFF button. 7. Select appropriate wash cycle / program (See Cycle Sequence Section). 8. Press the Start/Reset button. The LED display will flash intermittently to indicate the dishwasher is in "RUN" mode. NOTE: When you press the Start/Reset button to pause the unit during washing, the LED display will stop blinking and the dishwasher will stop working until the Start/Reset button is pressed again. Pausing the Wash Cycle / Program: In order to make any changes to the selected wash program / cycle, load additional items, or remove previously loaded items the dishwasher must be put in "PAUSE" status. The dishwasher can be put into PAUSE mode at any time during the wash cycle. To temporarily pause the washing process: 1. Press and hold the START / RESET button for approximately 3 seconds to cancel the existing program mode. 2. Make the necessary changes to the wash program / cycle selection or add/remove items from the dishwasher. 3. Ensure that the door is closed and the latch is fully engaged. 4. Press the START / RESET button once 5. The dishwasher will immediately resume operation using the most recently selected wash program / cycle. NOTE: If the door is opened at any time during the washing process, the dishwasher will automatically go to PAUSE mode. Once the door is closed and the latch is fully engaged the dishwasher will immediately resume operation. Although the dishwasher will be put in the PAUSE mode by opening the door, it is recommended that you instead follow the steps above to PAUSE the washing process. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
English
17
Operating Your Dishwasher
1. Ensure that all electrical, water, and drain connections have been
installed correctly before proceeding.
2. Load the dishwasher (See the “Loading your Dishwasher” section).
3. Make sure that the water supply is turned on to full pressure.
4. Add the appropriate amount of dishwasher detergent to the dispenser
(see Proper Use of Detergent Section).
5. Close the door and ensure that the door latch has engaged.
6. Turn the dishwasher ON by pressing the ON / OFF button.
7. Select appropriate wash cycle / program (See Cycle Sequence
Section).
8. Press the Start/Reset button. The LED display will flash intermittently to
indicate the dishwasher is in “RUN” mode.
NOTE:
When you press the Start/Reset button to pause the unit during
washing, the LED display will stop blinking and the dishwasher
will stop working until the Start/Reset button is pressed again.
Pausing the Wash Cycle / Program:
In order to make any changes to the selected wash program / cycle, load
additional items, or remove previously loaded items the dishwasher must
be put in “PAUSE” status. The dishwasher can be put into PAUSE mode at
any time during the wash cycle.
To temporarily pause the washing process:
1. Press and hold the START / RESET button for approximately 3 seconds
to cancel the existing program mode.
2. Make the necessary changes to the wash program / cycle selection or
add/remove items from the dishwasher.
3. Ensure that the door is closed and the latch is fully engaged.
4. Press the START / RESET button once
5. The dishwasher will immediately resume operation using the most
recently selected wash program / cycle.
NOTE:
If the door is opened at any time during the washing process,
the dishwasher will automatically go to PAUSE mode. Once the
door is closed and the latch is fully engaged the dishwasher will
immediately resume operation. Although the dishwasher will be
put in the PAUSE mode by opening the door, it is recommended
that you instead follow the steps above to PAUSE the washing
process.
OPERATING INSTRUCTIONS