Haier HDP18PA User Manual - Page 28

Steps, nstaHation - faucet adapter

Get Haier HDP18PA PDF manuals and user guides
UPC - 688057190624
View all Haier HDP18PA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Steps for _nstaHation Please read installation instructions carefully and follow the steps below to hook up your dishwasher, Caution: If, after completing these steps, you are unsure that unit is properly installed, contact a qualified installer. To ensure that your appliance is properly installed it is recommended that you get a certified installer. In order for this dishwasher to work, the following are required: • HOT WATER SUPPLY(cold can be use as well, see page#17 under "checking water temperature section") • DRAINAGE FOR USED WATER • ELECTRICITY:115 VOLT, 60Hz Outlet • GROUNDING • HORIZONTAL FLATSURFACE 1, You dishwasher must be placed on horizontal flat surface near by the sink, Placing the dishwasher as near to a sink as possible to allow for proper installation of the water inlet and drainage hoses. 2, Connect water inlet hose to the hot water faucet and to the water inlet valve on the back of the dishwasher. (Quick Connect Sink Adapter is supplied) 3, The other end of the drain hose must be placed properly in the sink or at your drain outlet in order to let used water drained out from the dishwasher. Note: The drain hose must be placed into a drainpipe or sink at least 1-1/2" in diameter. Use the gooseneck to hold hose in place, The minimum size of drainpipe must be 1-1/2" in diameter. The height of drainpipe must be 15-3/4" maximum, To avoid possible water back up, the drain hose must reach height of at least 36-1/2" maximum, 13n_ nTn • , Mr_ Dametere -K II. • ' ppe I I/2 0fsewage rainpipe 15 3/4 4. Plug in the dishwasher to a regular 115 Volt / 60 Hz, 15 Amp. Outlet. Note: 27 Inspect carefully for any water leak around and back of the machine. If any leak occurs, double check to see if any connections are loose, You may need to tighten any loose connections,

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
Steps
for
_nstaHation
Please
read
installation
instructions
carefully
and
follow
the steps
below
to hook
up
your
dishwasher,
Caution:
If, after
completing
these steps,
you
are unsure
that
unit
is properly
installed,
contact
a qualified
installer.
To ensure
that your
appliance
is
properly
installed
it is recommended
that
you
get a certified
installer.
In order for this dishwasher to work, the following
are required:
• HOT WATER SUPPLY(cold can be use as well, see page#17
under "checking
water temperature section")
• DRAINAGE FOR USED WATER
• ELECTRICITY:115 VOLT,60Hz Outlet
• GROUNDING
• HORIZONTAL FLATSURFACE
1, You dishwasher
must be placed
on
horizontal
flat surface
near
by the sink,
Placing
the dishwasher
as near
to a sink as possible
to allow
for
proper
installation
of the water
inlet
and
drainage
hoses.
2, Connect
water
inlet
hose to the hot
water
faucet
and
to the water
inlet
valve
on
the back
of the dishwasher.
(Quick
Connect
Sink
Adapter
is
supplied)
3, The other
end
of the drain
hose must be placed
properly
in the sink or at your
drain
outlet
in order
to let used water
drained
out
from
the dishwasher.
Note:
The drain
hose must be placed
into a drainpipe
or sink at least
1-1/2"
in
diameter.
Use the gooseneck
to hold
hose in place,
The minimum
size of
drainpipe
must be
1-1/2"
in diameter.
The height
of drainpipe
must be
15-3/4"
maximum,
To avoid
possible
water
back
up,
the drain
hose must
reach
height
of at least
36-1/2"
maximum,
13n_
nTn
•
,
Mr_
Dametere
0fsewage
•
'
ppe
I I/2
-K II.
rainpipe
15 3/4
4.
Plug in the
dishwasher
to a regular
115
Volt
/
60
Hz,
15
Amp.
Outlet.
Note:
Inspect
carefully
for any
water
leak
around
and
back
of the machine.
If any
leak
occurs,
double
check
to see if any
connections
are
loose,
You
may
need
to tighten
any
loose
connections,
27