Haier HLTD500AGW User Manual - Page 21

Step 2 - Connect To A Gas Supply Line, Gas Dryer Only

Get Haier HLTD500AGW PDF manuals and user guides View all Haier HLTD500AGW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

STEP 2 - CONNECT TO A GAS SUPPLY LINE (GAS DRYER ONLY) NOTE: Do not connect the dryer to an LP gas line without njrst converting the dryer with a conversion kit. An LP conversion kit must be installed by a qualinjed technician. NOTE: Apply a pipe-joint compound that that is resistant to the action of LP gas to all males threads. Do not use plumber's tape. 1. Turn the gas supply oNj by moving the shutoNj valve to the closed position. Closed Valve A Open Valve B 2. Disconnect and discard old Ǎexible gas connector. Replace with a new CSA(AGA) approved Ǎexible gas connector. 3. Remove the shipping cap from the gas inlet pipe at the rear of the dryer. 4. Connect a ƍ" NPT elbow to the gas inlet pipe on the dryer. Then connect a Ǎare adapter to the elbow. IMPORTANT: Use a pipe wrench to keep the dryer gas inlet pipe from twisting. Gas Inlet Pipe on the Dryer ƍ" NPT Elbow A C ƍ" NPT Flare Adapter B 5. Connect the dryer to the gas supply line with a Ǎexible gas connector. Flexible Gas Connector A 6. Tighten the Ǎexible gas connector using two adjustable wrenches. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
19
STEP 2 - CONNECT TO A GAS SUPPLY LINE
(GAS DRYER ONLY)
NOTE:
Do not connect the dryer to an LP gas line without
rst converting the
dryer with a conversion kit. An LP conversion kit must be installed by a quali
ed
technician.
NOTE:
Apply a pipe-joint compound that that is resistant to the action of LP gas to
all males threads. Do not use plumber’s tape.
1.
Turn the gas supply o
by moving the shuto
valve to the closed position.
Closed Valve
Open Valve
A
B
2.
Disconnect and discard old
exible gas connector. Replace with a new CSA(AGA)
approved
exible gas connector.
3.
Remove the shipping cap from the gas inlet pipe at the rear of the dryer.
4.
Connect a
" NPT elbow to the gas inlet pipe on the dryer. Then connect a
are
adapter to the elbow.
IMPORTANT:
Use a pipe wrench to keep the dryer gas inlet pipe from twisting.
Gas Inlet Pipe on
the Dryer
" NPT Elbow
" NPT Flare Adapter
A
B
C
5.
Connect the dryer to the gas supply line with a
exible gas connector.
Flexible Gas Connector
A
6.
Tighten the
exible gas connector using two adjustable wrenches.