Harman Kardon ADAPT PLUS Owners Manual Multilingual - Page 20

Android, WPS-PBC

Get Harman Kardon ADAPT PLUS PDF manuals and user guides View all Harman Kardon ADAPT PLUS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

SPEAKER SETUP If your iPhone or iPad has never connected to this Wi-Fi network before, you will need to enter the Wi-Fi password at this time. Most users will not need to enter this password. The speaker will automatically reboot and connect to the Wi-Fi network. Press Done in the top right corner of the popup to continue. If you are only using one Omni Bar+ or Omni Adapt+ in this room,continue to Source Setup on page 22. If you're setting up a wireless 5.1 surround system, the Controller app will guide you through this process again, then proceed to Wireless 5.1 Surround Setup on page 21. Android You will now see each speaker you have connected to AC power on the screen. Select any one of the speakers to see a list of available Wi-Fi networks. Choose the Wi-Fi network you wish to connect your Omni+ speakers to, then enter the Wi-Fi password. Every Omni+ speaker will reboot and connect to this Wi-Fi network. SSID PASSWORD Note: If you don't see the correct Wi-Fi network, make sure that the speaker is in range of the Wi-Fi router or access point. If you are only using one speaker in this room, continue to Source Setup on page 22. If you're setting up a wireless 5.1 surround system, proceed to Wireless 5.1 Surround Setup on page 21. WPS WPS is a simple way to connect your system to your home Wi-Fi network. To confirm whether your router supports WPS, look for the WPS logo or the letters WPS on your router. The Omni Bar+ and Omni Adapt+ support both WPS-PBC and WPS-PIN modes. WPS-PBC To connect your speaker via WPS-PBC mode: 1. Press the WPS button on your Wi-Fi router or access point. 2. Within one minute, press the WPS button on your Omni Bar+ or Omni Adapt+. 3. The Link button on the top of the speaker will begin to quickly flash for up to one minute. When the LED stops flashing and turns solid white, your speaker is connected. Note: This will connect your speaker to the network. After this is complete, you must open the Harman Kardon Controller app and set up a new room for this speaker. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
20
If your iPhone or iPad has never connected to this Wi-Fi network before, you will need to enter the
Wi-Fi password at this time. Most users will not need to enter this password.
The speaker will automatically reboot and connect to the Wi-Fi network. Press Done in the top right
corner of the popup to continue.
If you are only using one Omni Bar+ or Omni Adapt+ in this room,continue to Source Setup on
page 22. If you’re setting up a wireless 5.1 surround system, the Controller app will guide you through
this process again, then proceed to Wireless 5.1 Surround Setup on page 21.
Android
You will now see each speaker you have connected to AC power on the screen. Select any one of the
speakers to see a list of available Wi-Fi networks. Choose the Wi-Fi network you wish to connect your
Omni+ speakers to, then enter the Wi-Fi password. Every Omni+ speaker will reboot and connect
to this Wi-Fi network.
Note:
If you don’t see the correct Wi-Fi network, make sure that the speaker is in
range of the Wi-Fi router or access point.
If you are only using one speaker in this room, continue to Source Setup on
page 22. If you’re setting up a wireless 5.1 surround system, proceed to Wireless
5.1 Surround Setup on page 21.
WPS
WPS is a simple way to connect your system to your home Wi-Fi network. To confirm whether your
router supports WPS, look for the WPS logo or the letters WPS on your router. The Omni Bar+ and
Omni Adapt+ support both WPS-PBC and WPS-PIN modes.
WPS-PBC
To connect your speaker via WPS-PBC mode:
1.
Press the WPS button on your Wi-Fi router or access point.
2.
Within one minute, press the WPS button on your Omni Bar+ or Omni Adapt+.
3.
The Link button on the top of the speaker will begin to quickly flash for up to
one minute. When the LED stops flashing and turns solid white, your speaker
is connected.
Note:
This will connect your speaker to the network. After this is complete, you must open the
Harman Kardon Controller app and set up a new room for this speaker.
SPEAKER
SETUP
SSID
PASSWORD