Harman Kardon AVR 325 Owners Manual - Page 37

PROGRAMMING THE REMOTE

PROGRAMMING THE REMOTE

37

4. Press the button on the AVR 325 remote that you

wish to program. The

Program/SPL Indicator

c

will stop flashing.

5. Within five seconds, press and hold the button on

the original remote that you wish to “teach” into

the AVR 325 remote. When the

Program/SPL

Indicator

c

turns green three times, release

the button. The Program Indicator will then begin

to flash amber again.

NOTE:

If the


c

turns

red during Step 5, the programming was not suc-

cessful. Repeat the steps to see whether the code

will “take.”

6. Repeat Steps 4 though 6 for each button on the

source remote that you wish to transfer to the

AVR 325 remote.

7. Once all codes have been transferred from the

original source remote to the AVR 325 remote,

press the

Learn Button

.

8. Repeat Steps 1 through 7 for any additional

remotes you wish to “teach” into the AVR 325

remote.

Erasing Learned Codes

The AVR 325’s remote allows you to remove or erase

the code learned into a single button for a single device,

to remove or erase the code set for all the codes that

have been programmed into specific device buttons, or

to erase all commands that have been learned to all

devices.

To erase a single learned code from within a single

device’s settings, follow these steps:

1. Press and hold both the

Input Selector

e

within

which the individual button to be erased has been

programmed and the

Learn Button

.

2. When the red LED under the

Input Selector

turns

red and the


c

flashes

amber, release the buttons.

3. Press and release the

Input Selector

e

again for

the device within which the individual button to be

erased has been programmed.

4. Press the

7 Button

r

four times.

5. Press and release the individual button for which the

code is to be erased. The


c

will blink green two times and then return to

amber.

6. To erase other buttons within the same device, press

them as described in Step 5.

7. When all buttons to be erased have been pressed,

press the

Learn Button

to complete the

process.

To erase all codes within a single device, follow these

steps:

1. Press and hold both the

Input Selector

e

for

which you wish to erase the codes and the

Learn

Button

.


Input Selector

turns

red and the


c

flashes



Input Selector

e

again for

the device whose codes you wish to erase.

4. Press the

8 Button

r

four times.

5. The


c

will turn off and

the red light under the

Input Selector

will flash on

and off once to indicate that the codes have been

erased.

To erase all codes that have been programmed to all

devices in the remote, follow these steps:

1. Press any

Input Selector

e

for which you wish to

erase the codes and also the

Learn Button

.


Input Selector

turns

red and the


c

flashes



Input Selector

e

again for

the device whose codes you wish to erase.

4. Press the

9 Button

r

four times.

5. The


c

will turn off and

the red light under the

Input Selector

will flash on

and off once to indicate that the codes have been

erased.

Macro Programming

Macros enable you to easily repeat frequently used

combinations of commands with the press of a single

button on the AVR 325’s remote control. Once pro-

grammed, a macro will send out up to 19 different

remote codes in a predetermined sequential order

enabling you to automate the process of turning on

your system, changing devices, or other common

tasks. The AVR 325’s remote can store up to five

separate macro command sequences: one that is

associated with the

Power On Button

a

and four

more that are accessed by pressing the

Macro

Buttons

.

1. Press the

Mute Button

and the

Macro

Button

to be programmed or the

Power On

Button

a

at the same time. An

Input Selector

ef

will light red, and the

Program/SPL

Indicator

c

will flash amber.

2. Enter the steps for the macro sequence by press-

ing the button for the actual command step.

Although the macro may contain up to 19 steps,

each button press, including those used to change

devices, counts as a step. The

Program/SPL

Indicator

c

will flash green to confirm each

button press as you enter commands.

NOTE:

While entering commands for Power On/Off of

any device during a macro sequence, press the

Mute

Button

. DO NOT press the actual Power button.

3. When all the steps have been entered, press the

Sleep Button

j

to enter the commands. The

red light under the

Input Selectors

ef

will

blink and then turn off.

Example:

To program the Macro 1 button so that it

turns on the AVR 325, TV and a cable box, follow

these steps:

• Press the

Macro 1 Button

and

Mute

Button

at the same time and then release

them.

• Note that the


c

will

flash amber.

• Press the

AVR Selector

f

.

• Press the

Mute Button

to store the

AVR 325’s Power On command.

• Press the

VID 2 Input Selector Button

e

to

indicate the next command is for “TV Power On.”

• Press the

Mute Button

to store the TV

Power On Command.

• Press the

VID 3 Input Selector Button

e

to

indicate the next command is for “Cable Power On.”

• Press the

Mute Button

to store the Cable

Power On command.

• Press the

Sleep/Channel Up Button

j

to

complete the process and store the macro

sequence.

After following these steps, each time you press

the

Macro 1 Button

, the remote will send

the Power On/Off command.

31

43

43

43

43

31

43

31

43

31

42

42

42

42

42

Harman Kardon AVR 325 Owners Manual - Page 37

Macro Programming

Page 37 highlights