Harman Kardon AVR80 Owners Manual - Page 15

P-Scan, Delay, Menu Controls, Select, Screen Display, Panel Display, Test Noise, Speaker Select, - surround sound receiver

Get Harman Kardon AVR80 PDF manuals and user guides View all Harman Kardon AVR80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

AVR80 manual 11/01/98 13:01 Side 9 Remote Control Functions 9 ENGLISH n P-Scan: Press this button to automatically scan through the stations preset into the tuner memory. Press the button again to end the scan when the tuner stops at the desired station. o Memo: The memo button is used to enter stations to the tuner's preset memory in either the manual or automatic modes. It is also used in the process of clearing the memory. p Delay: This button controls the amount of sound delay to the rear (surround) channels. Press it to increase the delay in the steps shown in the main Information Display or on-screen graphics. q Menu Controls: These buttons control the action of the cursor or the selection of menu items when the receiver is being configured using the setup menus. r Select: This button chooses a menu and enters settings to the receiver's memory during system configuration. s Screen Display: Press this button to activate the on screen menu system. t Panel Display: Press this button to turn off all displays and indicators in the Information Display except for a small D I S P indication in the lower right corner of the display ¤ Press the button again to turn the display back on. Note that the display will briefly illuminate when a command is sent to the unit from the front panel or remote, even though the display is turned off. u Test Noise: Press this button to begin calibration of the output level for each channel. A test signal will immediately be heard from the left front speaker and the TEST indicator ™ will flash. v Speaker Select: When setting the system output levels, this button selects the speaker position being adjusted. Press it once to advance to the next speaker after each position is adjusted. w Level Adjust: When setting the system output levels, press these buttons in increase or decrease the output level. x Sending LED: This indicator should flash any time a button is pressed to confirm that a command is being sent to the receiver or another unit. If the light is dim or does not illuminate when a button is pressed the batteries in the remote should be replaced. y Learn LED: This indicator will illuminate when a button on the remote is being programmed with signals from another remote during the "learning" mode. The light will go out when the signal is received and memorized. z RDS PTY: Press this button to view the Programme Type information for stations transmitting RDS data. This button is also used for PTY Auto Search functions. ` RDS AF: This button initiates a search of alternate frequencies to find an eventually stronger signal for the station type currently selected.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
Remote Control Functions
9
ENGLISH
n
P-Scan:
Press this button to
automatically scan through the
stations preset into the tuner memory.
Press the button again to end the
scan when the tuner stops at the
desired station.
o
Memo:
The memo button is used
to enter stations to the tuner’s preset
memory in either the manual or
automatic modes. It is also used in the
process of clearing the memory.
p
Delay:
This button controls the
amount of sound delay to the rear
(surround) channels. Press it to
increase the delay in the steps shown
in the main Information Display or
on-screen graphics.
q
Menu Controls:
These buttons
control the action of the cursor or the
selection of menu items when the
receiver is being configured using the
setup menus.
r
Select:
This button chooses a
menu and enters settings to the
receiver’s memory during system
configuration.
s
Screen Display:
Press this
button to activate the on screen menu
system.
t
Panel Display:
Press this button
to turn off all displays and indicators in
the Information Display except for a
small
DISP
indication in the lower
right corner of the display
¤
Press the
button again to turn the display back
on. Note that the display will briefly
illuminate when a command is sent to
the unit from the front panel or remote,
even though the display is turned off.
u
Test Noise:
Press this button to
begin calibration of the output level for
each channel. A test signal will
immediately be heard from the left
front speaker and the
TEST
indicator
™
will flash.
v
Speaker Select:
When setting
the system output levels, this button
selects the speaker position being
adjusted. Press it once to advance to
the next speaker after each position is
adjusted.
w
Level Adjust:
When setting the
system output levels, press these
buttons in increase or decrease the
output level.
x
Sending LED:
This indicator
should flash any time a button is
pressed to confirm that a command is
being sent to the receiver or another
unit. If the light is dim or does not
illuminate when a button is pressed the
batteries in the remote should be
replaced.
y
Learn LED:
This indicator will
illuminate when a button on the
remote is being programmed with
signals from another remote during
the “learning” mode. The light will go
out when the signal is received and
memorized.
z
RDS PTY:
Press this button to
view the Programme Type information
for stations transmitting RDS data.
This button is also used for PTY Auto
Search functions.
`
RDS AF:
This button initiates a
search of alternate frequencies to find
an eventually stronger signal for the
station type currently selected.
AVR80 manual
11/01/98 13:01
Side 9