Home » HP Manuals » Desktops » HP 8000 » Manual Viewer

HP 8000 vPro Setup and Configuration for the 8000 Elite Business PC with Intel - Page 6

BIOS and follows the Intel ME Firmware Local Update option.

UPC - 884420665106

Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

5. Select Y. ME platform configuration allows IT personnel to configure ME features such as AMT/ASF selection, power options, firmware update capabilities, and so on. Figure 2 Intel ME Platform Configuration screen 6. Select Intel ME State Control, and then select Enabled. Default Setting = Enabled, Recommended Setting = Enabled This option enables or disables the ME and is used for diagnostic purposes. If set to Disabled, the ME is still initialized during POST, but is halted soon afterward so that it does not generate any traffic. If there is a problem that affects the ME, it can be removed from the system to eliminate it from the suspect list until root cause is found. Note that if the ME is disabled, then all AMT and ASF functions are also disabled. The system will not be remotely manageable. 7. Select Intel ME Firmware Local Update Qualifier. Default Setting = Always Open, Recommended Setting = Always Open This option allows the BIOS to override the ME Firmware Locale Update option and to permit local ME firmware updates. Always Open is the default and allows for as many local updates as the system BIOS allows, which is unlimited. Choosing Never Open or Restricted adds the Intel ME Firmware Local Update option, which can be set to Enable or Disable. By default it is Disabled. This option, along with the Qualifier, dictates whether ME firmware local updates are allowed. "Never Open" ignores what is set in the system BIOS and follows the Intel ME Firmware Local Update option. 6

Section	Page
vPro Setup and Configuration for the 8000 Elite Business PC with Intel vPro Processor Technology	1
Introduction	2
AMT Setup and Configuration	3
AMT System Phases	3
SMB Mode - AMT Setup and Configuration with MEBx	3
Password Guidelines	4
BIOS Prerequisite	4
SMB Mode - AMT Setup and Configuration Steps	5
1. Press Ctrl+P during POST to enter Manageability Engine BIOS Extension (MEBx) Setup. You can display this option only during POST if set in F10-Setup.	5
Figure 1 Intel MEBx Password Screen	5
2. Type the default password, which is admin. Passwords are case-sensitive.	5
3. Change the MEBx password. The new password must meet the Strong Password criteria defined in the Password Guidelines Section. Type the password twice for verification.	5
4. Select the Intel ME Platform Configuration. A window displays indicating that the system resets after configuration.	5
5. Select Y. ME platform configuration allows IT personnel to configure ME features such as AMT/ASF selection, power options, firmware update capabilities, and so on.	6
Figure 2 Intel ME Platform Configuration screen	6
6. Select Intel ME State Control, and then select Enabled.	6
7. Select Intel ME Firmware Local Update Qualifier.	6
8. Select Intel ME Features Control.	7
Figure 3 Intel ME Features Control Screen with AMT selected	7
9. Select Intel ME Power Control.	8
Figure 4 Intel ME Power Control Screen	8
10. Return to previous menu to exit the MEBx Setup and save ME configuration. The system will display an Intel ME Configuration Complete message and reboot. After the ME Configuration is complete, you can configure the AMT on the next boot.	9
11. Press Ctrl-P during POST to enter MEBx Setup again.	9
12. Type the MEBx password.	9
13. Select Intel AMT Configuration.	9
Figure 5 Intel AMT Configuration screen	9
14. Select Host Name, and then type a host name.	9
15. Select TCP/IP.	9
16. Select Provision Model.	11
17. Skip Un-Provision. This option returns the system to factory defaults.	11
18. Skip VLAN.	11
19. Select SOL/IDE-R.	11
20. Select Password Policy.	11
21. Select Secure Firmware Update, and then select Enabled.	12
22. Skip Set PRTC.	12
23. Select Idle Timeout.	12
24. Select Return to previous menu.	12
25. Select Exit, and then select Y to exit the MEBx Setup and save settings.	12
Intel AMT WebGUI	12
Connecting with the Intel AMT WebGUI - SMB Example	13
1. Power on an AMT system that has completed AMT Setup and Configuration.	13
2. Execute a Web browser from a separate system - a Management computer on the same subnet as the AMT computer.	13
3. Connect to the IP address specified in the MEBx and port of the AMT system.	13
4. Type the user name and password. The default username is admin and the password is what you set during AMT Setup in the MEBx.	14
Figure 6 Intel AMT WebGUI Screen	14
5. Review system information and/or make any necessary changes.	14
6. Select Exit.	14
Setup and Configuration Server	15
1. The AMT system sends out a “hello” message that includes the PSK over the network.	15
2. The SCS receives the “hello” message and verifies the PSK.	15
3. If the verification passes, then the SCS begins setup and configuration.	15
4. Once setup and configuration completes, the original PSK is deleted from the AMT client system, and a new PSK is given.	15
Setup and Configuration Server Availability	15
Enterprise Mode Setup and Configuration	16
Enterprise Mode - AMT Setup and Configuration Steps	16
1. Access the MEBx by pressing Ctrl-P during POST.	16
2. Type the default password, which is admin.	16
3. Change the MEBx password, following strong password guidelines.	16
4. Select Intel ME Platform Configuration.	16
5. In Intel ME State Control, select Enabled.	16
6. In Intel ME Firmware Local Update Qualifier, select Always Open.	16
7. Select Intel ME Features Control.	16
8. Select Intel ME Power Control.	16
9. Select Exit and save. The system displays the Intel ME Configuration Complete message, and then reboots.	16
10. Press Ctrl+P during POST to enter MEBx Setup again.	16
11. Type the MEBx password.	16
12. Select Intel AMT Configuration. The Intel AMT Configuration screen includes numerous options, which are available by scrolling down the menu.	17
Figure 7 Intel AMT Configuration Screen	17
Figure 8 Intel AMT Configuration Screen Continued	17
13. Select Host Name, and then type a host name	17
14. Select TCP/IP.	18
15. Select Provision Model.	18
16. Select Setup and Configuration.	18
Figure 9 Intel Setup and Configuration Screen	18
Figure 10 Intel TLS PSK Configuration Screen	20
17. Skip Un-Provision. This option returns the system to factory defaults. See the Return to Default section for more information about unprovisioning.	20
18. Skip VLAN.	21
19. Select SOL/IDE-R, and then select Y.	21
20. Select Password Policy.	21
21. Select Remote Firmware Update, and then select Enabled.	21
22. Skip Set PRTC.	21
23. Select Idle Timeout.	21
24. Select Return to previous menu.	22
25. Select Exit, and then select Y to exit the MEBx Setup and save settings. The system displays an Intel ME Configuration Complete message (only once) and reboots.	22
26. Turn off the system and remove power. The system is now in In-Setup Mode and is ready for deployment.	22
27. Plug the system into a power source and connect the network. Use the integrated Intel 82566DM NIC. Intel AMT does not work with any other NIC solution.	22
Provisioning Methods	24
Legacy	24
IT TLS-PSK	24
OEM TLS-PSK	24
USB Drive Key Set Up and Configuration	25
1. An IT technician inserts a USB drive key into a system with a management console.	25
2. The technician request local setup and configuration records from an S&CS through the console.	25
3. The S&CS:	25
4. The management console writes the password, PID, and PPS sets to a Setup.bin file in the USB drive key.	25
5. The technician takes the USB drive key to the staging area where new AMT platforms are located. The technician:	25
6. The system BIOS detects the USB drive key.	25
7. The system BIOS displays a message that automatic setup and configuration will occur.	26
8. MEBx processes the record.	26
9. MEBx writes a completion message to display.	26
10. The IT technician powers down the system. The system is now in In-Setup phase and is ready to be distributed to users in an Enterprise mode environment.	26
11. Repeat Step 5 if necessary (more than one system).	26
USB Drive Key Requirements	26
Remote Configuration	26
Remote Configuration: Bare-Metal vs. Delayed	27
Remote Configuration Time-outs in HP Systems	27
Remote Configuration Prerequisites	28
MEBx and Hashes	28
1. Press Ctrl+P for the MEBx, and then type the MEBx password.	28
2. Select Intel AMT Configuration.	28
3. Select Setup and Configuration.	28
4. Select TLS PKI.	28
Figure 11 Intel Remote Configuration Screen	29
1. Select Remote Configuration Enable/Disable.	29
2. Skip Manage Certificate Hashes.	29
3. Set PKI DNS Suffix. This option allows you to enter the PKI DNS Suffix of the SCS.	29
4. Select Return to the Previous Menu.	29
List of Supported CA Certificates	30
Return to Default	31
Figure 12 Intel AMT Unprovisioning Screen	31
1. Select Un-Provision, and then select the appropriate unprovision mode.	31
2. Select Return to previous menu.	31
3. Select Exit, and then select Y.	31
Full Return to Factory Defaults	32
Appendix A: Frequently Asked Questions	32
Appendix B: Power / Sleep / Global States Explained	34

Match case Limit results 1 per page

Select

. ME platform configuration allows IT personnel to configure ME features such as AMT/ASF

selection, power options, firmware update capabilities, and so on.

Figure 2

Intel ME Platform Configuration screen

Select

Intel ME State Control

, and then select

Enabled

Default Setting = Enabled, Recommended Setting = Enabled

This option enables or disables the ME and is used for diagnostic purposes. If set to

Disabled

, the

ME is still initialized during POST, but is halted soon afterward so that it does not generate any traffic.

If there is a problem that affects the ME, it can be removed from the system to eliminate it from the

suspect list until root cause is found.

Note that if the ME is disabled, then all AMT and ASF functions are also disabled. The system will not

be remotely manageable.

Select

Intel ME Firmware Local Update Qualifier.

Default Setting = Always Open, Recommended Setting = Always Open

This option allows the BIOS to override the ME Firmware Locale Update option and to permit local

ME firmware updates.

Always Open

is the default and allows for as many local updates as the system BIOS allows,

which is unlimited.

Choosing

Never Open

Restricted

adds the Intel ME Firmware Local Update option, which can

be set to Enable or Disable. By default it is Disabled. This option, along with the Qualifier, dictates

whether ME firmware local updates are allowed. "Never Open" ignores what is set in the system

BIOS and follows the Intel ME Firmware Local Update option.