HP BL2x220c HP ProLiant Servers Troubleshooting Guide - Page 94
Controller is Located in Special Video Slot
View all HP BL2x220c manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 94 highlights
Configuration Signature is Zero Description: ADU detected that NVRAM contains a configuration signature of zero. Old versions of the server setup utility could cause this. Action: Run the latest version of server setup utility to configure the controller and NVRAM. Configuration Signature Mismatch Description: The array accelerator board is configured for a different array controller board. The configuration signature on the array accelerator board does not match the one stored on the array controller board. Action: To recognize the array accelerator board, run ACU ("Array Configuration Utility" on page 67). Controller Communication Failure Occurred Description: Controller communication failure occurred. ADU was unable to successfully issue commands to the controller in this slot. Action: 1. Be sure all cables are properly connected and working. 2. Be sure the controller is working, and replace if needed. Controller Detected. NVRAM Configuration not Present Description: EISA NVRAM does not contain a configuration for this controller. Action: Run the server setup utility to configure the NVRAM. Controller Firmware Needs Upgrading Description: Controller firmware is below the latest recommended version. Action: Update the controller to the latest firmware version ("Firmware maintenance" on page 79). Controller is Located in Special "Video" Slot Description: Controller is installed in the slot for special video control signals. If the controller is used in this slot, LED indicators on the front panel may not function properly. Action: Install the controller into a different slot, and run the server setup utility to configure NVRAM. Then, run ACU ("Array Configuration Utility" on page 67) to configure the controller. Controller Is Not Configured Description: Controller is not configured. If the controller was previously configured and you change drive locations, a problem might exist with the placement of the drives. ADU examines each physical drive and looks for drives that have been moved to a different drive bay. Action: Look for messages indicating which drives have been moved. If no messages are displayed and drive swapping did not occur, run ACU ("Array Configuration Utility" on page 67) to configure the controller and run the server setup utility to configure NVRAM. Do not run either utility if you believe drive swapping has occurred. Error messages 94
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188