HP DL585 ProLiant DL585 Generation 2 Server User Guide - Page 45

Connect the power cord to the power supply., Install the power supply, and lock the lever.

Get HP DL585 - ProLiant - G2 PDF manuals and user guides
UPC - 882780448322
View all HP DL585 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

CAUTION: If only one power supply is installed, do not remove the power supply unless the server has been powered down. Removing the only operational power supply will cause an immediate power loss. NOTE: If you remove or replace the primary hot-plug power supply, use the T-15 Torx screwdriver provided with the server to remove the shipping screw. It is located just under the port-colored plastic handle of the power supply unit. 1. Remove the power supply blank. 2. Install the power supply, and lock the lever. 3. Connect the power cord to the power supply. 4. Secure the power cords to the retaining clip. 5. Connect the power cord to the power source. 6. Be sure that the power supply LED is green. 7. Be sure that the front panel external health LED is green. Hardware options installation 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Hardware options installation 45
CAUTION:
If only one power supply is installed, do not remove the power supply unless the
server has been powered down. Removing the only operational power supply will cause an
immediate power loss.
NOTE:
If you remove or replace the primary hot-plug power supply, use the T-15 Torx
screwdriver provided with the server to remove the shipping screw. It is located just under the
port-colored plastic handle of the power supply unit.
1.
Remove the power supply blank.
2.
Install the power supply, and lock the lever.
3.
Connect the power cord to the power supply.
4.
Secure the power cords to the retaining clip.
5.
Connect the power cord to the power source.
6.
Be sure that the power supply LED is green.
7.
Be sure that the front panel external health LED is green.