HP ENVY m6-w000 Maintenance and Service Guide - Page 45

Speakers, Remove the four Phillips PM2.5×5.0 screws

Get HP ENVY m6-w000 PDF manuals and user guides View all HP ENVY m6-w000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Speakers Description Speaker Kit (includes left and right speakers and cable) Spare part number 807535-001 Before removing the speakers, follow these steps: 1. Turn off the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect the power from the computer by unplugging the power cord from the computer. 3. Disconnect all external devices from the computer. 4. Remove the top cover (see Top cover on page 27). 5. Disconnect the battery. Remove the speakers: 1. Disconnect the speaker cable from the system board (1). 2. Remove the four Phillips PM2.5×5.0 screws (2) that secure the speakers to the computer. NOTE: Rubber gaskets fit around each screw (3). For installation, make sure the gaskets are properly installed. Component replacement procedures 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Speakers
Description
Spare part number
Speaker Kit (includes left and right speakers and cable)
807535-001
Before removing the speakers, follow these steps:
1.
Turn
off
the computer. If you are unsure whether the computer is
off
or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect the power from the computer by unplugging the power cord from the computer.
3.
Disconnect all external devices from the computer.
4.
Remove the top cover (see
Top cover
on page
27
).
5.
Disconnect the battery.
Remove the speakers:
1.
Disconnect the speaker cable from the system board
(1)
.
2.
Remove the four Phillips PM2.5×5.0 screws
(2)
that secure the speakers to the computer.
NOTE:
Rubber gaskets
fit
around each screw
(3)
. For installation, make sure the gaskets are properly
installed.
Component replacement procedures
35