HP Fortis 11 inch G9 Q Chromebook Maintenance and Service Guide - Page 44

Disconnect the four wireless antenna cables from the WWAN module integrated into the system board

Get HP Fortis 11 inch G9 Q Chromebook PDF manuals and user guides View all HP Fortis 11 inch G9 Q Chromebook manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Full hinge-up displays are not available as spare parts. Spare parts for displays are available only at the subcomponent level. NOTE: You can remove the bezel, display panel, and camera module without removing the display assembly from the computer. For more information, see Display subcomponents (without removing the display) on page 27. Before removing the display panel, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 24). 2. Remove the bottom cover (see Bottom cover on page 24). 3. Disconnect the battery cable from the system board (see Battery on page 25). Remove the display assembly: 1. Lift the plastic from the display connector on the system board (1), and then disconnect the display cable from the system board ZIF connector (2). 2. Remove the two Phillips M 2.0 × 2.5 screws (3) from the bracket that covers the connectors, and then remove the bracket (4). 3. Disconnect the four wireless antenna cables from the WWAN module integrated into the system board (5). Note that you need to remove only the far left and third from the left antenna. 4. Remove the four Phillips M2.5 × 4.0 screws (1) that secure the display assembly to the computer. 5. Remove the bracket from each hinge (2). 6. Open the computer to open the hinges to 90° (3). 7. Remove the antenna cable from the clip in the right hinge cavity (4). Display assembly 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
Full hinge-up displays are not available as spare parts. Spare parts for displays are available only at the
subcomponent level.
NOTE:
You can remove the bezel, display panel, and camera module without removing the display
assembly from the computer. For more information, see
Display subcomponents (without removing the
display)
on page
27
.
Before removing the display panel, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
24
).
2.
Remove the bottom cover (see
Bottom cover
on page
24
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
25
).
Remove the display assembly:
1.
Lift the plastic from the display connector on the system board
(1)
, and then disconnect the display cable
from the system board ZIF connector
(2)
.
2.
Remove the two Phillips M 2.0 × 2.5 screws
(3)
from the bracket that covers the connectors, and then
remove the bracket
(4)
.
3.
Disconnect the four wireless antenna cables from the WWAN module integrated into the system board
(5)
. Note that you need to remove only the far left and third from the left antenna.
4.
Remove the four Phillips M2.5 × 4.0 screws
(1)
that secure the display assembly to the computer.
5.
Remove the bracket from each hinge
(2)
.
6.
Open the computer to open the hinges to 90°
(3)
.
7.
Remove the antenna cable from the clip in the right hinge cavity
(4)
.
Display assembly
39