HP Integrity rx4640 Installation (Smart Setup) Guide, Windows Server 2003, v5. - Page 35

2 Installing the OS

This chapter provides instructions for installing the operating system (OS) using a headless

console, a GUI console, or a PXE-enabled NIC. This chapter also provides reinstallation instructions

for Windows Server 2003. Each method comprises a series of tasks, concluding with two tasks

that verify that the OS was installed correctly. You must install the HP Support Pack after installing

the OS. You must also install any operating system and security updates using the Smart Update

media.

NOTE:

HP Integrity servers must run Windows Server 2003 with either Service Pack 1 (SP1)

or Service Pack 2 (SP2). If you are running an earlier version of Windows Server 2003, you must

upgrade your operating system to SP1 or SP2. When updating to SP1 or SP2, perform the update

in the following order:

1.

Install the latest HP Integrity Support Pack.

2.

Reboot the machine.

3.

Install the desired Service Pack.

4.

Reboot the machine again.

5.

Use the Windows Update Service to ensure that you have the latest Microsoft updates.

If the Windows Server 2003 operating system has already been installed on your system, or if it

was pre-installed by HP before your system was delivered, you do not have to perform any of

the steps described in this chapter. You can proceed directly to Chapter 3 (

Chapter 3 “Installing

the Management Tools”

) and begin the installation of your management tools software.

If your Windows Server 2003 operating system is not already installed, or if you wish to reinstall

it for some reason, or if you wish to migrate to Windows Server 2003 from another operating

system, you will need to install the OS and OS updates using one or more of the following steps

described in this chapter, in the following order:

•

If you are installing your OS for the first time, or migrating from a different operating system:

—

Pick one of the following local installation options:

◦

“Installing from a headless console”

◦

“Installing from a GUI console”

—

Or, if you are not installing locally, pick one of the following remote installation options:

◦

“Installing from PXE”

◦

“Using Integrated Remote Console to install Windows on rx2660, rx3600, rx6600,

BL860c, and BL870c servers”

•

If you are reinstalling your operating system, pick on of the following options:

—

“Reinstalling from a headless console”

—

“Reinstalling from a GUI console”

•

After installing or reinstalling your operating system, perform the following tasks:

—

“Applying OS updates”

—

“Enabling Windows components”

—

“Updating firmware, drivers, and software”

—

See if you need to perform any final tasks here:

“Miscellaneous installation issues”

Installing from a headless console

Installing from a headless console involves booting from the HP Smart Setup media, running

EBSU, launching Windows Setup, loading OS files to the boot disk, and then booting the server

from the boot disk. You should be connected to the management processor (MP) of the target

server using a terminal emulation application such as HyperTerminal.

Installing from a headless console

35

Section	Page
Smart Setup Guide	1
Table of Contents	3
About This Document	11
Intended Audience	11
New and Changed Information in This Edition	11
Document Organization	11
Typographic Conventions	11
Related Information	12
Publishing History	13
HP Encourages Your Comments	13
1 Preparing for the installation	15
Choosing an installation method	15
Ensuring platform compatibility	16
Check hardware compatibility	16
Back up existing data	17
Choosing an installation environment	17
Choosing the Installation media	18
Using the Microsoft OS media	18
Using the HP Reinstallation media	18
Locating the Microsoft Certificate of Authenticity	18
Setting up a console	22
Set up a headless console	22
Set up the headless console using a null modem cable	22
Set up the headless console using a LAN	23
Set up the headless console using a Remote Serial Console (rx2660, rx3600, rx6600, BL860c, and BL870c only)	23
Set up a GUI console	23
Set up an Integrated Remote Console (rx2660, rx3600, rx6600, BL860c, and BL870c only)	25
Set up a Virtual Media (vMedia) drive	25
Setting up PXE/RIS	26
Set up a RIS server	27
Install RIS	28
Configure RIS	28
Authorize a RIS server in Active Directory	29
Use the Client Installation Wizard	29
Preparing the server hardware	30
Set up the boot drive	30
Boot to EFI	30
Locate the DVD/CD drive	31
Set ACPI flag to windows (cell-based servers only)	32
Set cell local memory to 100% (cell-based servers only)	32
Specify NIC for a network boot	32
2 Installing the OS	35
Installing from a headless console	35
Run EBSU	36
Run Windows Setup	38
Enter the product key	39
Installing from a GUI console	39
Run EBSU	39
Run Windows Setup	42
Specify server settings	42
Installing from PXE	43
Reinstalling from a headless console	43
Load the system image	44
Specify server settings	45
Reinstalling from a GUI console	46
Load the system image	46
Specify server settings	47
Applying OS updates	47
Enabling Windows components	48
Install TCP/IP	48
Install SNMP	48
Configure SNMP	49
Set IP addresses from a headless console	49
Set up and run a Remote Desktop Connection	49
Updating firmware, drivers, and software	50
Enable greater than 256 interrupts (cell-based servers only)	50
Update firmware	51
Update device drivers	51
Install the Integrity Support Pack (ISP)	52
Install updates from the web	53
Register for HP support notifications	53
Register for Microsoft security notifications	53
Register for Microsoft Windows Update	53
Miscellaneous installation issues	53
Using Integrated Remote Console to install Windows on rx2660, rx3600, rx6600, BL860c, and BL870c servers	53
Installing a Windows guest on an HP Integrity Virtual Machine host	54
Enabling hyperthreading on HP Integrity servers	55
Enable hyperthreading using EFI	55
Enable hyperthreading using Partition Manager	56
3 Installing the Management Tools	57
Installing System Management Homepage	57
Configure SMH after Support Pack installation	57
Install SMH separately	57
Initializing SMH	59
Installing the management agents	59
Configure management agents after Support Pack installation	60
Install management agents from Smart Setup media	60
Activating and configuring agents	60
Activating agents	60
Configuring the event notifier	61
Setting the agent SNMP data collection interval	63
Monitoring server processes	64
Sending SNMP traps to management applications via IP	65
Installing partition management tools	66
Install nPartition Commands Bundle from the Smart Setup media	67
Install Partition Manager Bundle from the Smart Setup media	67
Verifying the installation	68
Verify nPartition commands	68
Verify Partition Manager installation	68
4 Performing hot-plug operations	71
Before you begin	71
Adding a PCI card	72
Hardware interface for all HP Integrity servers except Superdome	72
Hardware interface for Superdome servers	73
Software interface	74
Removing a PCI card	74
Software interface for all HP Integrity servers except Superdome	74
Software interface for Superdome servers	74
Hardware interface for all HP Integrity servers except Superdome	74
Hardware interface for Superdome servers	75
A Preparing the server for Microsoft SQL Server 2005	77
SQL Server 2005 installation	77
Installing SQL Server from the command prompt	77
Installing SQL Server from the GUI	78
B EFI Utilities	81
Introduction to EFI	81
EFI Boot Manager	81
EFI Shell	81
Common EFI Shell commands	82
EFI-Based Setup Utility	85
Creating a new boot file using the EFI Shell	86
Verify successful boot file creation	87
C Management processor and Special Administration Console	89
Management processor	89
Accessing the MP	89
MP Commands	89
Special Administration Console	94

HP Integrity rx4640 Installation (Smart Setup) Guide, Windows Server 2003, v5. - Page 35

Installing the OS, Installing from a headless console

Page 35 highlights