HP LaserJet 1000 HP LaserJet 1000 Series - User Guide - Page 42

Status light patterns continued, Status lights, Condition of the printer, Action

Get HP LaserJet 1000 PDF manuals and user guides View all HP LaserJet 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Status light patterns (continued) Status lights Condition of the printer Action Fatal error Both lights are on. ● Unplug the printer for 5 minutes, and then plug it back in. ● If the printer still has an error, contact HP Support. See Service and support. USB cable is not connected or there is no power Both lights are off. ● Make sure that there is power. ● Unplug both ends of the power cord, and plug them back in. ● Unplug the power cord, disconnect both ends of the USB cable, reconnect both ends of the USB cable, and plug the power cord back in. CAUTION Before you connect the cable to the printer, always unplug the printer. Otherwise, the printer might be damaged. 40 Chapter 6 Troubleshooting the printer ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
40
Chapter 6 Troubleshooting the printer
ENWW
Fatal error
Both lights are on.
●
Unplug the printer for 5 minutes, and then
plug it back in.
●
If the printer still has an error, contact
HP Support. See
Service and support
.
USB cable is not connected or there is
no power
Both lights are off.
●
Make sure that there is power.
●
Unplug both ends of the power cord, and
plug them back in.
●
Unplug the power cord, disconnect both
ends of the USB cable, reconnect both ends
of the USB cable, and plug the power cord
back in.
CAUTION
Before you connect the cable to the printer,
always unplug the printer. Otherwise, the printer
might be damaged.
Status light patterns (continued)
Status lights
Condition of the printer
Action