HP LaserJet 5L HP LaserJet 5L - Printer User's Manual - Page 73

Labels should be arranged on the carrier sheet so that any exposed

Get HP LaserJet 5L PDF manuals and user guides View all HP LaserJet 5L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Adhesive Label Specifications Use the following guidelines when selecting labels: • The top sheet (printing surface) must be of copier quality and provide good toner adhesion. • The carrier sheet must be compatible with the temperatures and pressure of the fusing process, and must be coated for easy release of the top sheet. • The adhesive must be stable at the 392° F (200° C) temperature encountered for 0.1 second in the printer's fusing process, and must not produce emissions that exceed exposure levels or threshold limits established by OSHA and other safety agencies. Adhesives must not come into direct contact with any part of the printer. • Labels should be arranged on the carrier sheet so that any exposed spaces run lengthwise down the sheet. Using label stock with spaces between the horizontal rows of labels can result in labels peeling off during printing, causing serious jamming and possible printer damage. CAUTION Hewlett-Packard does not recommend removing any labels from the carrier sheet and then printing on the remaining labels. Table B-3 Adhesive Label Specifications Adhesive Caliper Curl Electrical Surface Resistivity Electrical Volume Resistivity Finishing Precision Fusing Compatibility Packaging Shelf Life Must not be on any external surfaces of the label before, during, or after printing. Label construction and die-cutting must not allow labels to peel off during transport, printing, or fusing. Must not exceed 0.007 in. (0.19 mm). In ream: flat within 0.2 in. (5 mm). 2.0 to 15 x 1010 ohm per square. 1.2 to 15 x 1011 ohm-cm. Cut sheet within +/- 0.03 in. (+/- 0.8 mm) of nominal and 0.20° square. All adhesives, carrier sheets, top sheets, and other materials used in label construction must be compatible with the heat and pressure of the fusing process. Materials must not discolor, melt, offset, or release hazardous emissions when heated to 392° F (200° C) for 0.1 second. Moisture-proof wrap to preserve properties. One year, maximum, stored at 72° F (22° C) and 50% R.H. Print Media B Specifications EN Print Media Specifications B-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Adhesive Label Specifications
Use the following guidelines when selecting labels:
•
The top sheet (printing surface) must be of copier quality and provide
good toner adhesion.
•
The carrier sheet must be compatible with the temperatures and
pressure of the fusing process, and must be coated for easy release of
the top sheet.
•
The adhesive must be stable at the 392° F (200° C) temperature
encountered for 0.1 second in the printer’s fusing process, and must
not produce emissions that exceed exposure levels or threshold limits
established by OSHA and other safety agencies. Adhesives must not
come into direct contact with any part of the printer.
•
Labels should be arranged on the carrier sheet so that any exposed
spaces run lengthwise down the sheet. Using label stock with spaces
between the horizontal rows of labels can result in labels peeling off
during printing, causing serious jamming and possible printer damage.
CAUTION
Hewlett-Packard does not recommend removing any labels from the
carrier sheet and then printing on the remaining labels.
Adhesive
Must not be on any external surfaces of the label before, during, or after printing.
Label construction and die-cutting must not allow labels to peel off during transport,
printing, or fusing.
Caliper
Must not exceed 0.007 in. (0.19 mm).
Curl
In ream: flat within 0.2 in. (5 mm).
Electrical Surface Resistivity
2.0 to 15 x 10
10
ohm per square.
Electrical Volume Resistivity
1.2 to 15 x 10
11
ohm-cm.
Finishing Precision
Cut sheet within +/- 0.03 in. (+/- 0.8 mm) of nominal and 0.20° square.
Fusing Compatibility
All adhesives, carrier sheets, top sheets, and other materials used in label
construction must be compatible with the heat and pressure of the fusing process.
Materials must not discolor, melt, offset, or release hazardous emissions when
heated to 392° F (200° C) for 0.1 second.
Packaging
Moisture-proof wrap to preserve properties.
Shelf Life
One year, maximum, stored at 72° F (22° C) and 50% R.H.
Table B-3
Adhesive Label Specifications
B
Print Media
Specifications
EN
Print Media Specifications
B-5