HP Latex 360 Users Guide - Page 69

The edge holders, WARNING, Place edge holders for the 310 or 330 printer

Get HP Latex 360 PDF manuals and user guides View all HP Latex 360 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

6. Select the category and name of the substrate you are loading. The rest of the assisted load procedure is the same as in the normal load procedure. See Load a roll into the printer on page 50. The edge holders The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress. They are recommended for textile and double-sided printing (even if the front panel does not suggest them), and are not normally necessary in other situations. They can be used with the platen or with the ink collector. When not in use, they should be stored inside the printer, to the left and right respectively, to avoid substrate jams. It is also a good idea to store the edge holders when no substrate is loaded, in case you later forget and leave them installed by mistake. NOTE: The edge holders extend 7 mm over the edge of the substrate. You should set a minimum left and right margin of 7 mm (0.3 in) in the RIP when using edge holders, otherwise the printer could try to print on the edge holders. If you choose to use them, you should move them into position when prompted by the front panel (this prompt appears when the Use edge holders checkbox has been checked). Open the window, place the edge holders, then close the window. The edge holders should be placed on the platen so that they slightly overlap the left and right edges of the substrate. There are marks on the printer to show where to place them. The edge holders for each printer model are the same, but they are installed in different ways. WARNING! Avoid moving parts. Handle fragile parts with care. You are recommended to wear gloves. Moving part Fragile For more safety information, please see Safety precautions on page 3 Wear gloves Place edge holders for the 310 or 330 printer 1. There is a hole on the left for the edge holders. Insert an edge holder vertically into the hole. ENWW The edge holders 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
6.
Select the category and name of the substrate you are loading.
The rest of the assisted load procedure is the same as in the normal load procedure. See
Load a roll into the
printer
on page
50
.
The edge holders
The edge holders are designed to prevent the edges of the substrate from rising while printing is in progress.
They are recommended for textile and double-sided printing (even if the front panel does not suggest them),
and are not normally necessary in other situations. They can be used with the platen or with the ink collector.
When not in use, they should be stored inside the printer, to the left and right respectively, to avoid substrate
jams. It is also a good idea to store the edge holders when no substrate is loaded, in case you later forget and
leave them installed by mistake.
NOTE:
The edge holders extend 7 mm over the edge of the substrate. You should set a minimum left and
right margin of 7 mm (0.3 in) in the RIP when using edge holders, otherwise the printer could try to print on
the edge holders.
If you choose to use them, you should move them into position when prompted by the front panel (this
prompt appears when the
Use edge holders
checkbox has been checked). Open the window, place the edge
holders, then close the window.
The edge holders should be placed on the platen so that they slightly overlap the left and right edges of the
substrate. There are marks on the printer to show where to place them.
The edge holders for each printer model are the same, but they are installed in different ways.
WARNING!
Avoid moving parts. Handle fragile parts with care. You are recommended to wear gloves.
Moving part
Fragile
Wear gloves
For more safety information, please see
Safety precautions
on page
3
Place edge holders for the 310 or 330 printer
1.
There is a hole on the left for the edge holders. Insert an edge holder vertically into the hole.
ENWW
The edge holders
63