HP Latex 800 Introductory Information - Page 4

General safety guidelines, Electrical shock hazard, Heat hazard - printer

Get HP Latex 800 PDF manuals and user guides View all HP Latex 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

This equipment is not suitable for use in locations where children are likely to be present. For any maintenance or part replacement, follow the instructions provided in HP documentation to minimize safety risks and to avoid damaging the printer. General safety guidelines Please read these safety guidelines carefully. There are no operator-serviceable parts inside the printer except those covered by HP's Customer Self Repair program: see http://www.hp.com/go/selfrepair. Refer servicing of other parts to qualified service personnel. Turn off the printer and call your service representative in any of the following cases: ● A power cord or plug is damaged. ● The curing enclosures are damaged. ● The printer has been damaged by an impact. ● There is any mechanical or enclosure damage. ● Liquid has entered the printer. ● There is smoke or an unusual smell coming from the printer. ● The printer has been dropped or the curing module has been damaged. ● The printer is not operating normally. Turn off the printer in either of the following cases: ● During a thunderstorm ● During a power failure Take special care with zones marked with warning labels. Electrical shock hazard WARNING! The internal circuits of curing zones, curing driver and built-in power supply operate at hazardous voltages capable of causing death or serious personal injury. The printer uses two power cords. Unplug both power cords before servicing the printer. To avoid the risk of electric shock: ● The printer must be connected to earthed mains outlets only. ● Do not attempt to dismantle the curing modules. ● Do not remove or open any closed system covers or plugs. ● Do not insert objects through slots in the printer. Heat hazard The curing subsystems of the printer operate at high temperatures and can cause burns if touched. To avoid personal injury, take the following precautions: 2 HP Latex 700 & 800 Printer Series ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
This equipment is not suitable for use in locations where children are likely to be present.
For any maintenance or part replacement, follow the instructions provided in HP
documentation to minimize safety risks and to avoid damaging the printer.
General safety guidelines
Please read these safety guidelines carefully.
There are no operator-serviceable parts inside the printer except those covered by HP’s
Customer Self Repair program: see
go/selfrepair
. Refer servicing of
other parts to quali
fi
ed service personnel.
Turn o
ff
the printer and call your service representative in any of the following cases:
●
A power cord or plug is damaged.
●
The curing enclosures are damaged.
●
The printer has been damaged by an impact.
●
There is any mechanical or enclosure damage.
●
Liquid has entered the printer.
●
There is smoke or an unusual smell coming from the printer.
●
The printer has been dropped or the curing module has been damaged.
●
The printer is not operating normally.
Turn o
ff
the printer in either of the following cases:
●
During a thunderstorm
●
During a power failure
Take special care with zones marked with warning labels.
Electrical shock hazard
WARNING!
The internal circuits of curing zones, curing driver and built-in power supply
operate at hazardous voltages capable of causing death or serious personal injury.
The printer uses two power cords. Unplug both power cords before servicing the printer.
To avoid the risk of electric shock:
●
The printer must be connected to earthed mains outlets only.
●
Do not attempt to dismantle the curing modules.
●
Do not remove or open any closed system covers or plugs.
●
Do not insert objects through slots in the printer.
Heat hazard
The curing subsystems of the printer operate at high temperatures and can cause burns if
touched. To avoid personal injury, take the following precautions:
2
HP Latex 700 & 800 Printer Series
ENWW